Sputter-deposited thin film nitinol constructs with various micropatterns were fabricated to evaluate their effect on the vessel wall in vivo when used as a covering for commercially available stents. Thin film nitinol constructs were used to cover stents and deployed in non-diseased swine arteries. Swine were sacrificed after approximately four weeks and the thin film nitinol-covered stents were removed for histopathologic evaluation. Histopathology revealed differences in neointimal thickness that correlated with the thin film nitinol micropattern. Devices covered with thin film nitinol with a lateral x vertical length = 20 x 40 µm diamond pattern had minimal neointimal growth with well-organized cell architecture and little evidence of ongoing inflammation. Devices covered with thin film nitinol with smaller fenestrations exhibited a relatively thick neointimal layer with inflammation and larger fenestrations showed migration of inflammatory and smooth muscle cells through the micro fenestrations. This "proof-of-concept" study suggests that there may be an ideal thin film nitinol porosity and pore geometry to encourage endothelialization and incorporation of the device into the vessel wall. Future work will be needed to determine the optimal pore size and geometry to minimize neointimal proliferation and in-stent stenosis.
Biomedical coatings for orthopedic implants should facilitate osseointegration and mitigate implant-induced inflammatory reactions. Cerium oxide (CeO2) ceramics possess anti-oxidative properties and can be used to decrease mediators of inflammation, which makes them attractive for biomedical applications. In our work, two kinds of CeO2 incorporated hydroxyapatite coatings (HA-10Ce and HA-30Ce) were prepared via plasma spraying technique and the effects of CeO2 addition on the responses of bone mesenchymal stem cells (BMSCs) and RAW264.7 macrophages were investigated. An increase in CeO2 content in the HA coatings resulted in better osteogenic behaviors of BMSCs in terms of cell proliferation, alkaline phosphatase (ALP) activity and mineralized nodule formation. RT-PCR and western blot analysis suggested that the incorporation of CeO2 may promote the osteogenic differentiation of BMSCs through the Smad-dependent BMP signaling pathway, which activated Runx2 expression and subsequently enhanced the expression of ALP and OCN. The expression profiles of macrophages cultured on the CeO2 modified coating revealed a tendency toward a M2 phenotype, because of an upregulation of M2 surface markers (CD163 and CD206), anti-inflammatory cytokines (TNF-α and IL-6) and osteoblastogenesis-related genes (BMP2 and TGF-β1) as well as a downregulation of M1 surface markers (CCR7 and CD11c), proinflammatory cytokines (IL-10 and IL-1ra) and reactive oxygen species production. The results suggested the regulation of BMSCs behaviors and macrophage-mediated responses at the coating’s surface were associated with CeO2 incorporation. The incorporation of CeO2 in HA coatings can be a valuable strategy to promote osteogenic responses and reduce inflammatory reactions.
Redesigned multifunctional biopolymers represent a novel building bridge for interdisciplinary collaborations in biomaterials development. We prepared fluorescein-grafted polyurethane scaffolds (PU-C1, PU-C5, and PU-B1) to meet both clinical needs and biological safety evaluations, using different contents of calcein and different synthesis procedures for potential biomedical tracing. X-ray diffraction, infrared, X-ray photoelectron spectroscopy, nuclear magnetic resonance, scanning electron microscopy, and light microscopy were used to analyze the composition and structure of polyurethanes, as well as to observe their morphology with and without biomarkers. Fluorescence spectrophotometer and fluorescence microscopy were used to detect the fluorescence characteristics. The results showed that the grafting of calcein significantly affected the chemical structure and fluorescence sensitivities of copolymers. When compared to calcein, which was added before synthesis (PU-C1), the marker that was added during the extender process (PU-B1) presented higher fluorescence efficiency. Both PU-C5 and PU-B1 exhibited strong fluorescent response and good cytocompatibility in vitro and in vivo, with no interference from the autofluorescence of tissues after 4 weeks of implantation. The fluorescence-marked material can be used to continuously and noninvasively monitor the dynamic changes in polymers, which provides a way to clearly trace the material or to distinguish between the material and tissue in vivo.
The 3D printing process is highlighted nowadays as a possibility to generate individual parts with complex geometries. Moreover, the development of 3D printing hardware, software and parameters permits the manufacture of parts that can be not only used as prototypes, but are also made from materials that are suitable for implantation. In this way, this study investigates the process involved in the production of patient-specific craniofacial implants using calcium phosphate cement, and its dimensional accuracy. The implants were previously generated in a computer-aided design environment based on the patient’s tomographic data. The fabrication of the implants was carried out in a commercial 3D powder printing system using alfa-tricalcium phosphate powder and an aqueous solution of Na2HPO4 as a binder. The fit of the 3D printed implants was measured by three-dimensional laser scanning and by checking the right adjustment to the patient’s anatomical biomodel. The printed parts presented a good degree of fitting and accuracy.
In this work, we explored the potential of thermo-sensitive PLGA-PEG-PLGA with sol-gel transition temperature around 32℃ as an intramuscular vaccine delivery system by using ovalbumin as a model antigen. First, in vitro release test showed that the PLGA-PEG-PLGA-deriving hydrogels could release ovalbumin in vitro in a more sustainable way. From fluorescence living imaging, 50–200 mg/mL of PLGA-PEG-PLGA formulations could release antigen in a sustainable manner in vivo, suggesting that the PLGA-PEG-PLGA hydrogel worked as an antigen-depot. Further, the sustainable antigen release from the PLGA-PEG-PLGA hydrogels increased antigen availability in the spleens of the immunized mice. The intramuscular immunization results showed that 50–200 mg/mL of PLGA-PEG-PLGA formulations promoted significantly more potent antigen-specific IgG immune response. In addition, 200 mg/mL of PLGA-PEG-PLGA formulation significantly enhanced the secretion of both Th1 and Th2 cytokines. From in vitro splenocyte proliferation assay, 50–200 mg/mL of PLGA-PEG-PLGA formulations all initiated significantly higher splenocyte activation. These results indicate that the thermo-sensitive and injectable PLGA-PEG-PLGA hydrogels (particularly, 200 mg/mL of PLGA-PEG-PLGA-based hydrogel) own promising potential as an intramuscular vaccine delivery system.
The aim of this study was to prepare and characterize highly porous clinoptilolite/poly(-caprolactone)-poly(ethylene glycol)-poly(-caprolactone) composite scaffolds. Scaffolds with different clinoptilolite contents (10% and 20%) were fabricated with reproducible solvent-free powder compression/particulate leaching technique. The scaffolds had interconnective porosity in the range of 55–76%. Clinoptilolite/poly(-caprolactone)-poly(ethylene glycol)-poly(-caprolactone) scaffolds showed negligible degradation within eight weeks and displayed less water uptake and higher bioactivity than poly(-caprolactone)-poly(ethylene glycol)-poly(-caprolactone) scaffolds. The presence of clinoptilolite improved the mechanical properties. Highest compressive strength (5.6 MPa) and modulus (114.84 MPa) were reached with scaffold group containing 20% clinoptilolite. In vitro protein adsorption capacity of the scaffolds was also higher for clinoptilolite/poly(-caprolactone)-poly(ethylene glycol)-poly(-caprolactone) scaffolds. These scaffolds had 0.95 mg protein/g scaffold adsorption capacity and also higher osteoinductivity in terms of enhanced ALP, OSP activities and intracellular calcium deposition. Stoichiometric apatite deposition (Ca/P=1.686) was observed during cellular proliferation analysis with human fetal osteoblasts cells. Thus, it can be suggested that clinoptilolite/poly(-caprolactone)-poly(ethylene glycol)-poly(-caprolactone) composite scaffolds could be promising carriers for enhancement of bone regeneration in bone tissue engineering applications.
Dicalcium phosphate dihydrate particles functionalized with triethyleneglycol dimethacrylate were synthesized and added to a photocurable mixture of bisphenol-A glycidyl dimethacrylate and triethyleneglycol dimethacrylate with the purpose of developing a resin composite capable of releasing calcium and phosphate ions to foster dental remineralization. Particle functionalization would minimize the deleterious effect of adding low cohesive strength nano-structured particles with no chemical interaction with the organic matrix on the material’s mechanical properties. The results showed that calcium release over 28 days was not impaired by particle functionalization. A statistically significant 32% increase in strength was recorded with the use of functionalized dicalcium phosphate dihydrate in comparison to the material containing non-functionalized particles. However, the strength of the unfilled resin was not matched by the composite with functionalized particles. Elastic modulus increased with particle incorporation, regardless of functionalization. Degree of conversion and optical properties (total transmittance and color change/E) of the resin-based materials were not affected by the addition of dicalcium phosphate dihydrate particles (functionalized or not).
Owing to the excellent bioactive properties of recombinant human bone morphogenetic proteins (rhBMPs), dentistry considers them as a fascinating adjuvant alternative for enhancing bone regeneration and bone-to-implant junction in the early implantation stages. However, stable loading and delivery efficiency of rhBMPs on the implant surfaces involve major concerns because of the harsh wearing condition under load during implantation. In this study, to achieve successful rhBMP-2 delivery, a nanoporous surface structure is introduced on the sandblasting with large grit and acid-etching (SLA)-treated titanium (Ti) surface via the tantalum (Ta) target-ion induced plasma sputtering (TIPS) technique. Unlike oxidation-induced surface nanoporous fabrications on a Ti surface, TIPS-treated surfaces provide excellent structural unity of the nanoporous structure with the substrate due to their etching-based fabrication mechanism. SLA/TIPS-treated Ti exhibits distinct nanoporous structures on the microscale surface geometry and better hydrophilicity compared with SLA-treated Ti. A sufficiently empty nanoporous surface structure combined with the hydrophilic property of SLA/TIPS-treated Ti facilitates the formation of a thick and uniform coating layer of rhBMP-2 on the surface without any macro- and microcoagulation. Compared with the SLA-treated Ti surface, the amount of coated rhBMP-2 increases up to 63% on the SLA/TIPS-treated Ti surface. As a result, the in vitro pre-osteoblast cell response of the SLA/TIPS-treated Ti surface, especially cell adhesion and differentiation behaviors, improves remarkably. A bone-regenerating direct comparison between the rhBMP-2-coated SLA-treated and SLA/TIPS-treated Ti is conducted on a defective dog mandible model. After 8 weeks of implantation surgery, SLA/TIPS-treated Ti with rhBMP-2 exhibits a better degree of contact area for the implanted bone, which mineralizes new bones around the implant. Quantitative results of bone-in-contact ratio and new bone volume also show significantly higher values for the SLA/TIPS-treated Ti with the rhBMP-2 specimen. These results confirm that an SLA/TIPS-treated surface is a suitable rhBMP-2 carrier for a dental implant to achieve early and strong osseointegration of Ti dental implants.
In this study, soy protein isolate was hydrolyzed by compound enzymes to give aqueous soy protein with low molecular weights. Folic acid modified and free soy protein nanoparticles were successfully prepared by a desolvation method as target-specific drug delivery, respectively. Ultraviolet spectrophotometry demonstrated that folic acid was successfully grafted onto soy protein. The shape and size of folic acid modified soy protein nanoparticles were detected by transmission electron microscopy, scanning electron microscope, and dynamic light scattering. In addition, a series of characteristics including kinetic stability, pH stability, and time stability were also performed. Doxorubicin was successfully loaded into folic acid modified soy protein nanoparticles, and the encapsulation and loading efficiencies were 96.7% and 23%, respectively. Doxorubicin-loaded folic acid modified soy protein nanoparticles exhibited faster drug release rate than soy protein nanoparticles in PBS solution (pH = 5). The tumor penetration and antitumor experiments were done using three-dimensional multicellular tumor spheroids as the in vitro model. The results proved that folic acid modified soy protein nanoparticles display higher penetration and accumulation than soy protein nanoparticles, therefore possessing efficient growth inhibitory ability against multicellular tumor spheroids.
Congenital diaphragmatic hernia is a severe disease requiring diaphragm replacement mostly with expanded polytetrafluoroethylene. Unfortunately, the recurrence rate is high due to prosthesis failure with significant morbidity for the child. To provide a better understanding of the integration and possible failure processes of the biomaterial implanted in humans, we conducted electron microscopical and mechanical assessments on a prosthesis explant from a child with congenital diaphragmatic hernia presenting a recurrence. Our findings show a major penetration of connective tissue into the expanded polytetrafluoroethylene on the rough side, whereas the smooth side presents few tissue colonization. This penetration is more important in the central area (area A) with large collagen bundles and layers, in comparison to the peripheral areas without prosthesis failure (area B), where few extracellular matrix is produced. The connective tissue penetrates the prosthesis in depth. In contrast, the peripheral areas with prosthesis failure (area C) show very few cells and extracellular matrix, with an oriented organization in comparison to areas A and B. Obviously, the forces applied on the implanted material modulate the cellular behavior of the newly developed tissues. Atomic force microscopic measurements of the biomaterials’ surfaces may explain some cellular behaviors according to areas with or without failure.
The coronary artery stent has been widely used in clinic. In-stent restenosis was mainly caused by the excessive proliferation of smooth muscle cell and the inflammation due to the metal ion released from stent scaffold of the drug-eluting stent. Thus, to reduce the in-stent restenosis and promote the vascular endothelialization have become a hot research point in this area. In this paper, a nano-TiO2 ceramic coating was deposited on 316L stainless steel to reduce the metal ion release and to inhibit the inflammation reaction. An endothelia cell selective adhesion peptide Arg-Glu-Asp-Val (REDV) coating was prepared on the ceramic coating by a polydopamine technology to promote the endothelialization. The corrosion test indicated that nano-TiO2 ceramic film could effectively decrease the nickel ion released from 316L stainless steel. REDV/TiO2 coating could promote the endothelial cell adhesion and proliferation, meanwhile REDV/TiO2 coating could also increase the nitric oxide concentration. Bare metal stent, TiO2-coated stent and REDV/TiO2-coated stent were implanted in the iliac arteries of rabbit model. In-stent restenosis and re-endothelialization were evaluated at 28 days post-implantation of the stents. The results showed that REDV/TiO2-coated stents could effectively reduce in-stent restenosis and promote re-endothelialization in comparison with TiO2-coated drug-eluting stent and bare metal stent. These results suggest that REDV/TiO2-coated drug-eluting stent maybe a good choice of the application for coronary artery disease.
The blood–brain barrier is the interface between the blood and brain, impeding the passage of most circulating cells and molecules, protecting the latter from foreign substances, and maintaining central nervous system homeostasis. However, its restrictive nature constitutes an obstacle, preventing therapeutic drugs from entering the brain. Usually, a large systemic dose is required to achieve pharmacological therapeutic levels in the brain, leading to adverse effects in the body. As a consequence, various strategies are being developed to enhance the amount and concentration of therapeutic compounds in the brain. One such tool is nanotechnology, in which nanostructures that are 1–100 nm are designed to deliver drugs to the brain. In this review, we examine many nanotechnology-based approaches to the treatment of neurodegenerative diseases. The review begins with a brief history of nanotechnology, followed by a discussion of its definition, the properties of most reported nanomaterials, their biocompatibility, the mechanisms of cell–material interactions, and the current status of nanotechnology in treating Alzheimer’s, Parkinson’s diseases, and amyotrophic lateral sclerosis. Of all strategies to deliver drug to the brain that are used in nanotechnology, drug release systems are the most frequently reported.
Safe and efficient drug delivery in a controllable fashion, especially remote and repeatable switch of on-demand drug release, is the subject of widespread attention. A kind of magnetic nanoparticles (DOX-Cit/CuS@Fe3O4-NPs) simultaneously consisted of Cit/CuS@Fe3O4 and doxorubicin (DOX) was presented. The drug release from DOX-Cit/CuS@Fe3O4-NPs could be successfully triggered by the presence of gelatinase, showing great promise for tumor-targeted drug release through an enzymatic degradation mechanism. Compared with free DOX, DOX-Cit/CuS@Fe3O4-NPs could not only specially deliver Cit/CuS@Fe3O4 and DOX into MCF-7 cells, but also could greatly improve the quantity of ROS produced in MCF-7 cells under of 980 nm laser irradiation. DOX-Cit/CuS@Fe3O4-NPs also had highly selective accumulation at tumor tissue of S180 tumor-bearing mice, which were along with a magnet near the tumor site. Furthermore, when combined with NIR laser irridation, DOX-Cit/CuS@Fe3O4-NPs showed a higher antitumor efficacy than the individual therapies in vitro and in vivo. This study showed that DOX-Cit/CuS@Fe3O4-NPs could be used as a platform for tumor chemotherapy, photothermal and photodynamic therapy.
Daily subcutaneous injection of human growth hormone has been used for the treatment of growth hormone deficiency and growth failure but has led to poor patient compliance and renal toxicity. Thus, it is crucial to develop favorable growth hormone delivery systems to improve patient compliance. In the present study, to increase the oral bioavailability of growth hormone and improve patient compliance, enteric-coated capsules filled with monomethoxyl poly(ethylene glycol)-b-poly(L-lactide-co-glycolide) nanoparticles were prepared to facilitate oral growth hormone delivery. The nanoparticles were less than 100 nm in size, exhibited narrow polydispersity indices < 0.3, and showed a zeta potential of –4.87 mV. The highest efficiency of growth hormone encapsulation achieved in this study was nearly 70%. An in vitro release experiment showed that adequate amounts of growth hormone were retained under simulated gastric conditions and significant amounts of growth hormone were released under simulated intestinal conditions. The bioavailability of encapsulated growth hormone relative to subcutaneously injected growth hormone in Sprague-Dawley rats was 11.06%. Thus, the use of poly(ethylene glycol)-b-poly(L-lactide-co-glycolide) nanoparticles yielded promising results, and these agents should be investigated further regarding their potential as an oral growth hormone delivery system in the future.
Electrospinning is one of the efficient processes to fabricate polymeric fibrous scaffolds for several biomedical applications. Several studies have published to demonstrate drug release from electrospun scaffolds. Blends of natural and synthetic electrospun fibers provide excellent platform to combine mechanical and bioactive properties. Drug release from polymer blends is a complex process. Drug release from polymer can be dominated by one or more of following mechanisms: polymer erosion, relaxation, and degradation. In this study, electrospun polycaprolactone (PCL)–gelatin blends are investigated to understand release mechanism of Rhodamine B dye. Also, this article summarizes the effect of high-pressure carbon dioxide on drug loading and release from PCL–gelatin fibers. Results indicate that release media diffusion is a dominant mechanism for PCL–gelatin electrospun fibers. Thickness of electrospun mat becomes critical for blends with gelatin. As gelatin is highly soluble in water and has tendency of gelation, it affects diffusion of release media in and out of scaffold. This article is a key step forward in understanding release from electrospun blends.
Germanium (Ge)-based glass ionomer cements have demonstrated the ability to balance strength with extended setting times, a unique set of characteristics for aluminum-free glass ionomer cements. However, the mechanical properties of current Ge-based glass ionomer cements significantly deteriorate over time, which jeopardizes their clinical potential. This work explores the effect of incrementally decreasing the Si:Ge ratio in the glass phase of zinc-silicate glass ionomer cements to identify potential mechanisms responsible for the time-induced mechanical instability of Ge-based glass ionomer cements. The influence of Ge was evaluated on the basis of changes in mechanical properties and molecular architecture of the cements over a 180-day period. It was observed that the compressive strength and modulus of the cements were sustained when Si:Ge ratios were ≥1:1, but when Si:Ge ratios are <1:1 these properties decreased significantly over time. These mechanical changes were independent of structural changes in the glass ionomer cement matrices, as the level of metal–carboxylate crosslinks remained constant over time across the various Si:Ge ratios explored. However, it was noted the temporal decline of mechanical properties was proportional to the increased release of degradation byproducts, in particular Ge that was released from the cements in substantially greater quantities than other glass constituents. Unexpectedly, the slowest setting cement (Si:Ge 1:1) was also the strongest; behavior that is uncommon in Si-based glass ionomer cements, supports the potential of Ge-containing glass ionomer cements as injectable bone cements in applications such as percutaneous vertebroplasty.
Stent insertion and chemical agents of ethylene diamine tetraacetic acid and sodium cholate for dissolving common bile duct stone diseases through extra biliary tract infusion have been believed a relatively effective therapeutics for the clinical symptom. Core-shell nanofibers produced by co-axial electrospinning to deliver chemical drugs, biomacromolecules, genes and even cells have been reported for various advanced drug delivery system and tissue engineering applications. In the present study, poly (lactide-co--caprolactone) (PLCL) core-shell nanofiber-coated film of stent, loaded with ethylene diamine tetraacetic acid and sodium cholate in core layer, was fabricated by co-axial electrospinning for treating gallstone disease. Image of laser scanning confocal microscopy and transmission electron microscopy demonstrated core-shell structure of drug-loaded nanofiber. Fourier transform infrared spectra and the thermogravimetric analysis proved ethylene diamine tetraacetic acid and sodium cholate to be successfully loaded in nanofibers. Morphology of nanofibers after a period of degradation still keeps good shape. Drugs can continuously release for around five days, which was proved significant effectiveness for dissolving gallstone. Besides, unobvious cytotoxicity was exhibited from MTT results and cell kept good morphology in vitro research. The present coated stent showed a bright prospect for dissolving the biliary stone.
This work considered the effect of both increasing additions of Strontium (Sr2+) and incubation time on solubility and both antibacterial and osteo-stimulatory effects of a series of glasses based on the B2O3–P2O5–CaCO3–Na2CO3–TiO2–SrCO3 series. The amorphous nature of all the glasses was confirmed by X-ray diffraction. Discs of each glass were immersed in de-ionized water for 1, 7 and 30 days, and the water extracts were used for ion release profiles, pH measurements and cytotoxicity testing. Atomic absorption spectroscopy was employed to detect the release of Na+, Ca2+ and Sr2+ ions from the glasses with respect to maturation, which indicated that the addition of Sr2+ retarded solubility of the glass series. This effect was also confirmed by weight loss analysis through comparing the initial weight of glass discs before and after periods of incubation. The incorporation of Sr2+ in the glasses did not influence the pH of the water extracts when the glasses were stored for up to 30 days. Cytotoxicity testing with an osteoblastic cell line (MC3T3-E1) indicated that glasses with the higher (20 mol% and 25 mol%) Sr2+ incorporation promoted proliferation of osteoblast cells, while the glasses with lower Sr2+ contents inhibited cell growth. The glass series, except for Ly-B5 (which contained the highest Sr2+ incorporation; 25 mol%), were bacteriostatic against S. aureus in the short term (1–7 days) as a result of the dissolution products released.
The optimization of tamoxifen citrate entrapment and its release from biodegradable poly(
Injectable calcium phosphate cements have been used as a valid alternative to autologous bone grafts for bone augmentation with the additional advantage of enabling minimally invasive implantation procedures and for perfectly fitting the tissue defect. Nevertheless, they have low biodegradability and lack adequate biochemical signaling to promote bone healing and remodeling. In previous in vitro studies, we observed that the incorporation of platelet lysate directly into the cement paste or loaded in hyaluronic acid microspheres allowed to modulate the cement degradation and the in vitro expression of osteogenic markers in seeded human adipose derived stem cells. The present study aimed at investigating the possible effect of this system in new bone formation when implanted in calvarial bilateral defects in rats. Different formulations were assessed, namely plain calcium phosphate cements, calcium phosphate cements loaded with human platelet lysate, hybrid injectable formulations composed of the calcium phosphate cement incorporating hyaluronin acid non-loaded microparticles (20% hyaluronin acid) or with particles loaded with platelet lysate. The degradability and new bone regrowth were evaluated in terms of mineral volume in the defect, measured by micro-computed tomography and histomorphometric analysis upon 4, 8 and 12 weeks of implantation. We observed that the incorporation of hyaluronin acid microspheres induced an overly rapid cement degradation, impairing the osteoconductive properties of the cement composites. Moreover, the incorporation of platelet lysate induced higher bone healing than the materials without platelet lysate, up to four weeks after surgery. Nevertheless, this effect was not found to be significant when compared to the one observed in the sham-treated group.
3D printing of biological architectures that mimic the structural and functional features of in vivo tissues is of great interest in tissue engineering and the development of transplantable organ constructs. Printable bio-inks that are compatible with cellular activities play critical roles in the process of 3D bio-printing. Although a variety of hydrogels have been used as bio-inks for 3D bio-printing, they inherit poor mechanical properties and/or the lack of essential protein components that compromise their performance. Here, a hybrid Matrigel–agarose hydrogel system has been demonstrated that possesses both desired rheological properties for bio-printing and biocompatibility for long-term (11 days) cell culture. The agarose component in the hybrid hydrogel system enables the maintenance of 3D-printed structures, whereas Matrigel provides essential microenvironments for cell growth. When human intestinal epithelial HCT116 cells are encapsulated in the printed Matrigel–agarose constructs, high cell viability and proper cell spreading morphology are observed. Given that Matrigel is used extensively for 3D cell culturing, the developed 3D-printable Matrigel–agarose system will open a new way to construct Matrigel-based 3D constructs for cell culture and tissue engineering.
Hyaluronic acid is the main polysaccharide present in the connective tissue. Besides its structural function as backbone of the extracellular matrix, hyaluronic acid plays staple roles in several biological processes including the modulation of inflammation and wound healing processes. The application of hyaluronic acid in regenerative medicine, either as cells and/or drug/growth factors delivery vehicles, relies on its ability to be cross-linked using a plethora of reactions, producing stable hydrogels. In this work, we propose a novel method for the production of hyaluronic acid microparticles that presents several advantages over others that have been used. Basically, droplets of hyaluronic acid solution produced with a nozzle are collected in an isopropanol dehydration bath, and stabilized after crosslinking with adipic acid dihydrazide, using a cabodiimide-based chemistry. The size and morphology of the hyaluronic acid microparticles produced by this method varied with the molecular weight and concentration of the hyaluronic acid solution, the nozzle chamber pressure, the distance between the nozzle and the crosslinking solution, and the number of crosslinking steps. The degree of crosslinking of the hyaluronic acid microparticles produced was tunable and allowed to control the rate of the degradation promoted by hyaluronidase. Moreover, the particles were loaded with platelet lysate, a hemoderivative rich in cytokines with interest for regenerative medicine applications. The hyaluronic acid microparticles showed potential to bind selectively to positively charged molecules, as the factors present in the platelet lysate. It is envisioned that these can be further released in a sustained manner by ion exchange or by the degradation of the hyaluronic acid microparticles matrix promoted by extracellular matrix remodeling.
A functionally modified peptide-conjugated hydrogel system was fabricated with oxidized alginate/gelatin loaded with biphasic calcium phosphate to improve its biocompatibility and functionality. Sodium alginate was treated by controlled oxidation to transform the cis-diol group into an aldehyde group in a controlled manner, which was then conjugated to the amine terminus of glycine–arginine–glycine–aspartic. Oxidized alginate glycine–arginine–glycine–aspartic was then combined with gelatin-loaded biphasic calcium phosphate to form a hydrogel of composite oxidized alginate/gelatin/biphasic calcium phosphate that displayed enhanced human adipose stem cell adhesion, spreading and differentiation. 1H nuclear magnetic resonance and electron spectroscopy for chemical analysis confirmed that the glycine–arginine–glycine–aspartic was successfully grafted to the oxidized alginate. Co-delivery of glycine–arginine–glycine–aspartic and human adipose stem cell in a hydrogel matrix was studied with the results indicating that hydrogel incorporated modified with glycine–arginine–glycine–aspartic and seeded with human adipose stem cell enhanced osteogenesis in vitro and bone formation in vivo.
Microbial contamination has been a major challenge in a wide variety of fields such as biomedical and biomaterial applications. The development of biomaterials that possess excellent antibacterial ability and biocompatibility is of great importance to enhance the service life of biomaterials. In this study, the main protein component of red blood cells, hemoglobin (Hb), was employed to prepare Ag–Hb nanocomposites as novel biocompatible antiseptics. The formation of Ag–Hb nanocomposites on the titanium substrate are confirmed by field-emission scanning electron microscopy, Fourier transformed infrared spectroscopic, contact angles, and inductively coupled plasma atomic emission spectrometry analysis. The Ag–Hb titanium shows potent antibacterial ability against planktonic bacteria in the suspension and ability to prevent bacterial adhesion. Moreover, the Ag–Hb titanium shows excellent biocompatibility, which supports healthy osteoblast cellular activity and osteoblast differentiation. The results indicate that the Ag–Hb nanocomposites can be potentially useful for the fabrication of biomaterials for long-term applications.
In this study, a calcium polyphosphate cement (CpPC) consisting of basic components was investigated to assess its potential for hard tissue regeneration. The added basic components for improving the structural stability, which controlled the setting time, where the setting reaction resulted in the formation of amorphous structure with a re-constructed polyphosphate. Moreover, the characteristics were controlled by the composition, which determined the polyphosphate structure. CpPC exhibited outstanding dissolution rate compared with the common biodegradable cement, brushite cement (2.5 times). Despite high amounts of dissolution products, no significant cytotoxicity ensued. Induction of calcification in MG-63 cells treated with CpPC, the level of calcification increased with increasing CpPC dissolution rate. Induced calcification was observed also in CpPC-treated ST2 cells, in contrast with MG-63 and ST2 treated with brushite cement, for which no calcification was observed. In vivo tests using a rat calvarial defect model showed that resorbed CpPC resulted in favorable host responses and promoted bone formation. Additionally, there was a significant increase in defect closure, and new bone formation progressed from CpPC mid-sites as well as defect margins. From these results, CpPC exhibits significant potential as biodegradable bone substitute for bone regeneration.
The aim of this study was to characterise the elution profiles of antibiotics in combination with pharmaceutical grade calcium sulphate beads in phosphate buffered saline and other physiological solutions which more closely mimic the in vivo environment. Synthetic recrystallised calcium sulphate was combined with vancomycin hydrochloride powder and tobramycin sulphate solution and the paste was formed into 3 mm diameter hemispherical beads. Then 2 g of beads were immersed in 2 ml of either phosphate buffered saline, Dulbecco’s Modified Eagle Medium or Hartmann’s solution and incubated at 37℃ for up to 21 days. At a range of time points, eluent was removed for analysis by liquid chromatography-mass spectrometry (LC-MS). Tobramycin sulphate and vancomycin hydrochloride release was successfully quantified against standard curves from solutions eluted in all three physiological media (phosphate buffered saline, Dulbecco’s Modified Eagle Medium and Hartmann’s solution) during incubation with calcium sulphate beads. One hour eluate concentrations were high, up to 2602 µg/ml for tobramycin in phosphate buffered saline and 7417 µg/ml for vancomycin, whereas in DMEM, the levels of tobramycin were 2458 µg/ml and 4401 µg/ml for vancomycin. The levels in HRT were 2354 µg/ml for tobramycin and 5948 µg/ml for vancomycin. The results show highest levels of antibiotic elution over the first 24 h, which gradually diminish over the following 21 days.
Injectable thermo-sensitive hydrogels have a potential application in bone tissue engineering for their sensitivities and minimal invasive properties. Human dental pulp stem cells have been considered a promising tool for tissue reconstruction. The objective of this study was to investigate the proliferation and osteogenic differentiation of dental pulp stem cells in injectable thermo-sensitive chitosan/β-glycerophosphate/hydroxyapatite hydrogel in vitro. The chitosan /β-glycerophosphate hydrogel and chitosan/β-glycerophosphate/hydroxyapatite hydrogel were prepared using the sol-gel method. The injectability of chitosan /β-glycerophosphate hydrogel and chitosan/β-glycerophosphate/hydroxyapatite hydrogel was measured using a commercial disposable syringe. Scanning electron microscopy was used to observe the inner structure of hydrogels. Then dental pulp stem cells were seeded in chitosan /β-glycerophosphate hydrogel and chitosan/β-glycerophosphate/hydroxyapatite hydrogel, respectively. The growth of dental pulp stem cells was periodically observed under an inverted microscope. The proliferation of dental pulp stem cells was detected by using an Alamar Blue kit, while cell apoptosis was determined by using a Live/Dead Viability/Cytotoxicity kit. The osteogenic differentiations of dental pulp stem cells in chitosan /β-glycerophosphate hydrogel and chitosan/β-glycerophosphate/hydroxyapatite hydrogel were evaluated by alkaline phosphatase activity assay and mRNA expression of osteogenesis gene for 21 days in osteogenic medium. The results indicated that there was no significant difference between chitosan /β-glycerophosphate hydrogel and chitosan/β-glycerophosphate/hydroxyapatite hydrogel in injectability. Cells within the chitosan/β-glycerophosphate/hydroxyapatite hydrogel displayed a typical adherent cell morphology and rapid proliferation with high cellular viability after 14 days of culture. Dental pulp stem cells seeded in chitosan/β-glycerophosphate/hydroxyapatite hydrogels had a higher alkaline phosphatase activity and better up-regulation of gene expression levels of Runx-2, Collagen I, alkaline phosphatase and osteocalcin than in chitosan /β-glycerophosphate hydrogels after osteogenic differentiation. These results demonstrated that the chitosan/β-glycerophosphate/hydroxyapatite hydrogel had excellent cellular compatibility and the superiority in promoting dental pulp stem cells osteogenic differentiation in vitro, showing that the combination of dental pulp stem cells and chitosan/β-glycerophosphate/hydroxyapatite hydrogel has the potential to be used for bone tissue engineering.
An in situ formed hydrogel was synthesized by sodium alginate and cysteine methyl ester, which turned the sodium alginate into thiolated alginate (SA-SH). SA-SH can in situ formed into hydrogel (SA-SS-SA) with a large amount of water through covalent bond in less than 20 s. The structure characterization showed that the mechanism of SA-SH gelation was thiol-disulfide transformation. The rheology and cytotoxicity experiments of SA-SS-SA hydrogel were also investigated, which indicated that SA-SS-SA hydrogel had an appropriate mechanical strength as well as an excellent biocompatibility. The SA-SS-SA hydrogel would degrade under certain conditions after a few days and its mechanism was disulfide alkaline reduction. Finally, the hemostatic property of SA-SH was tested by rat tail amputation experiment. The time to hemostasis of rat reduced from 8.26 min to 3.24 min, which proved that SA-SH had an excellent hemostatic property.
Nanocomposite scaffolds of TiO2 and hydroxyapatite nanoparticles with alginate as the binding agent were fabricated using the freeze drying technique. TiO2, hydroxyapatite and alginate were used in the ratio of 1:1:4. The scaffolds were characterized using X-ray diffraction, fourier transform infrared spectroscopy, and scanning electron microscopy. The biocompatibility of the scaffolds was evaluated using cell adhesion and MTT assay on osteosarcoma (MG-63) cells. Scanning electron microscopy analysis revealed that cells adhered to the surface of the scaffolds with good spreading. The mechanical properties of the scaffolds were investigated using dynamic mechanical analysis. The swelling ability, porosity, in vitro degradation, and biomineralization of the scaffolds were also evaluated. The results indicated controlled swelling, limited degradation, and enhanced biomineralization. Further, drug delivery studies of the scaffolds using the chemotherapeutic drug methotrexate exhibited an ideal drug release profile. These scaffolds are proposed as potential candidates for bone tissue engineering and drug delivery applications.
Biofunctionalized nanofibers with a desired biological function can be used as a tissue engineering scaffold due to their small fiber diameters and porous structure. In the present study, poly(-caprolactone)/poly(m-anthranilic acid) nanofibers were biofunctionalized with covalent immobilization of bone morphogenetic protein-2 (BMP-2) through 1-ethyl-3-(dimethyl-aminopropyl) carbodiimide hydrochloride/N-hydroxysuccinimide activation. Fourier transform infrared analysis of the nanofiber surfaces confirmed the successful immobilization. The amount of immobilized BMP-2 was determined with bicinchoninic acid protein assay. The nanofibers before and after BMP-2 immobilization were non-cytotoxic and enhanced the attachment and proliferation of Saos-2 cells. Biofunctionalization of nanofibers with BMP-2 promoted in vitro osteogenic activity. The alkaline phosphatase activity and calcium mineralizatio of cells after 14 days of in vitro culture were enhanced on nanofibers with immobilized BMP-2.
Ti–C:H coatings were deposited on original, nitrided, and polished-nitrided AISI 316L stainless steel substrates using a closed field unbalanced magnetron sputtering system. Sliding friction wear tests were performed in 0.89 wt.% NaCl solution under a load of 30 N against AISI 316L stainless steel, Si3N4, and Ti6Al4V balls, respectively. The electrochemical properties of the various specimens were investigated by means of corrosion tests performed in 0.89 wt.% NaCl solution at room temperature. Finally, the biocompatibility properties of the specimens were investigated by performing cell culturing experiments using purified mouse leukemic monocyte macrophage cells (Raw264.7). In general, the results showed that plasma nitriding followed by Ti–C:H coating deposition provides an effective means of improving the wear resistance, anti-corrosion properties, and biocompatibility performance of AISI 316L stainless steel.
In this study, we investigated the phase separation phenomenon of silk fibroin/poly (-caprolactone) electrospinning solution to improve the performance of silk fibroin/poly (-caprolactone) electrospun nanofibers. It showed that phase separation does occur in just a few hours in the silk fibroin/poly (-caprolactone)/formic acid mixture solution. Acetic acid, small molecule nonsolvent for silk fibroin, was first introduced to silk fibroin/poly (-caprolactone)/formic acid solution, a homogeneous solution without separation for over several days was achieved after mixing for 5 h. The morphology and composition of the silk fibroin/poly (-caprolactone) and acetic acid-modified silk fibroin/poly (-caprolactone) fibrous scaffolds were examined by scanning electron microscopy, Fourier transform infrared spectroscopy and thermal gravimetric analyzer. Attachment and proliferation of mouse osteoblast MC3T3-E1 cells were tested by scanning electron microscopy and cytotoxity assay. The results indicated that the phase separation of silk fibroin/poly (-caprolactone) solution might led to inhomogeneous morphology and composition of the composite scaffolds, and the inhomogeneity of the silk fibroin/poly (-caprolactone) scaffolds with formic acid as solvent had a remarkable difference on cell adhesion and proliferation. In contrast, there was no significant difference among the silk fibroin/poly (-caprolactone) scaffolds with formic acid/acetic acid as solvent because of their good consistency in fiber morphology and composition. These obtained silk fibroin/poly (-caprolactone) nanofibers had small average diameter of 190 ± 40 nm. The obtained results proved that this study provided a facile and effective approach to achieve compositionally homogeneous silk fibroin/poly (-caprolactone) scaffolds with formic acid as solvent for effective applications.
Achieving a radiographic gross total resection in high-grade gliomas improves overall survival. Many technologies such as intraoperative microscope, intraoperative ultrasound, fluorescence imaging, and intraoperative magnetic resonance imaging have been applied to improve tumor resection. However, most commercial available magnetic resonance imaging contrast agents have limited permeability across the blood–brain barrier and are cleared rapidly from circulation. Fluorescence imaging discriminates tumor from normal tissue and provides a promising new strategy to maximize sage surgical resection of tumor. However, the penetration depth of fluorescence imaging is generally low.
In this study, a new type of magnetite NaGdF4:Yb3+,Er3+,Li+@NaGdF4 (UCNPs) core-shell nanoparticles, coated with SiO2 and further functionalized with glioma and blood–brain barrier targeting motifs, was prepared for dual-modal in vivo upconversion imaging and magnetic resonance imaging.
The as-prepared multifunctional upconversion nanoparticles (UCNPs@SiO2-CX-Lf) were biocompatible, showed strong upconversion luminescence under excitation of 980 nm, and provided high signal-to-noise ratio in vivo. Moreover, UCNPs@SiO2-CX-Lf nanoparticles showed a high relaxivity of 1.25 S-1 mM-1 and were successfully applied as contrast agent for magnetic resonance imaging in tumor xenograft rat model with prolonged tumor signal enhancement. In vivo and magnetic resonance imaging Upconversion Luminescence (UCL) imaging results indicated that these particles can across the blood–brain barrier, bind to glioma, gave bright UCL signal and T1 magnetic resonance imaging contrast.
Targeted UCL and magnetic resonance imaging dual-modal in vivo imaging using Yb3+/Er3+/Li+ codoped NaGdF4 core-shell nanostructure can serve as a platform technology for the next generation of intraoperative probes for image-guided tumor resection.
The endogenous electric field plays a determining role in impacting biological functions including communication with the physiological system, brain, and bone regeneration by influencing cellular functions. From this perspective, the objective of the study described here is to elucidate the effect of external electric field under dynamic conditions, in providing a guiding cue to osteoblasts in terms of cell–cell interactions and synthesis of prominent adhesion and cytoskeleton proteins. This was accomplished using pulsed direct current electric field of strength 0.1–1 V/cm. The electric field provided guided cue to the cells to migrate toward cathode. Membrane blebbing or necrosis was nearly absent in the vicinity of cathode at 0.1 and 0.5 V/cm electric field strength. Moreover, a higher cell proliferation as well as higher expression of vinculin and densely packed actin stress fibers was observed. At anode, the cells though healthy but expression of actin and vinculin was less. We underscore for the first time that the biological functionality can be favorably modulated on 3D printed scaffolds in the presence of electric field and under dynamic conditions with consequent positive effect on cell proliferation, growth, and expression level of prominent proteins.
Poly(lactic-co-glycolic) acid (PLGA) is synthesized via melt polycondensation directly from lactic acid and glycolic acid with a feed molar ratio of 75/25. Bovine serum albumin, which is used as model protein, is entrapped into the poly(lactic-co-glycolic acid) microspheres with particle size of 260.9 ± 20.0 nm by the double emulsification method. Then it is the first report of producing more carboxyl groups by poly(lactic-co-glycolic acid) surface hydrolysis. The purpose is developing poly(lactic-co-glycolic acid) microspheres surface, which is modified with chitosan by chemical reaction between carboxyl groups and amine groups. The particle size and the positive zeta potential of the poly(lactic-co-glycolic acid)/chitosan microspheres are 388.2 ± 35.6 nm and 10.4 ± 2.9 mV, respectively. The drug loading ratio and encapsulation efficacy of poly(lactic-co-glycolic acid)/chitosan microspheres are 36.3% and 57.5%, which are higher than PLGA microspheres. Furthermore, the drug burst release of poly(lactic-co-glycolic acid)/chitosan microspheres at 10 h is decreased to 21.72% while the corresponding value of the poly(lactic-co-glycolic acid) microsphere is 64.56%. These results reveal that surface hydrolysis modification of poly(lactic-co-glycolic acid) is an efficient method to improve the negative potential and chemical reaction properties of the polymer. And furthermore, this study shows that chitosan-modified poly(lactic-co-glycolic acid) microspheres is a promising system for the controlled release of pharmaceutical proteins.
Magnesium alloys are modern biocompatible materials suitable for orthopaedic implants due to their biodegradability in biological environment. Many studies indicate that there is a high demand to design magnesium alloys with controllable in vivo corrosion rates and required mechanical properties. A solution to this challenge can be sought in the development of metal matrix composites based on magnesium alloys with addition of relevant alloying elements and bioceramic particles. In this study, the corrosion mechanisms along with corrosion protection methods in magnesium alloys are discussed. The recently developed magnesium alloys for biomedical applications are reviewed. Special attention is given to the newest research results in metal matrix composites composed of magnesium alloy matrix and calcium phosphates, especially hydroxyapatite or tricalcium phosphate, as the second phase with emphasis on the biodegradation behavior, microstructure and mechanical properties in view of potential application of these materials in bone implants.
Recently, three-dimensional graphene interconnected network has attracted great interest as a scaffold structure for tissue engineering due to its high biocompatibility, high electrical conductivity, high specific surface area and high porosity. However, free-standing three-dimensional graphene exhibits poor flexibility and stability due to ease of disintegration during processing. In this work, three-dimensional graphene is composited with polydimethylsiloxane to improve the structural flexibility and stability by a new simple two-step process comprising dip coating of polydimethylsiloxane on chemical vapor deposited graphene/Ni foam and wet etching of nickel foam. Structural characterizations confirmed an interconnected three-dimensional multi-layer graphene structure with thin polydimethylsiloxane scaffold. The composite was employed as a substrate for culture of L929 fibroblast cells and its cytocompatibility was evaluated by cell viability (Alamar blue assay), reactive oxygen species production and vinculin immunofluorescence imaging. The result revealed that cell viability on three-dimensional graphene/polydimethylsiloxane composite increased with increasing culture time and was slightly different from a polystyrene substrate (control). Moreover, cells cultured on three-dimensional graphene/polydimethylsiloxane composite generated less ROS than the control at culture times of 3–6 h. The results of immunofluorescence staining demonstrated that fibroblast cells expressed adhesion protein (vinculin) and adhered well on three-dimensional graphene/polydimethylsiloxane surface. Good cell adhesion could be attributed to suitable surface properties of three-dimensional graphene/polydimethylsiloxane with moderate contact angle and small negative zeta potential in culture solution. The results of electrochemical study by cyclic voltammetry showed that an oxidation current signal with no apparent peak was induced by fibroblast cells and the oxidation current at an oxidation potential of +0.9 V increased linearly with increasing cell number. Therefore, the three-dimensional graphene/polydimethylsiloxane composite exhibits high cytocompatibility and can potentially be used as a conductive substrate for cell-based electrochemical sensing.
Extracellular matrix materials such as decellularized cartilage (DCC) and chondroitin sulfate (CS) may be attractive chondrogenic materials for cartilage regeneration. The goal of the current study was to investigate the effects of encapsulation of DCC and CS in homogeneous microsphere-based scaffolds, and to test the hypothesis that encapsulation of these extracellular matrix materials would induce chondrogenesis of rat bone marrow stromal cells. Four different types of homogeneous scaffolds were fabricated from microspheres of poly(D,L-lactic-co-glycolic acid): Blank (poly(D,L-lactic-co-glycolic acid) only; negative control), transforming growth factor-β3 encapsulated (positive control), DCC encapsulated, and CS encapsulated. These scaffolds were then seeded with rat bone marrow stromal cells and cultured for 6 weeks. The DCC and CS encapsulation altered the morphological features of the microspheres, resulting in higher porosities in these groups. Moreover, the mechanical properties of the scaffolds were impacted due to differences in the degree of sintering, with the CS group exhibiting the highest compressive modulus. Biochemical evidence suggested a mitogenic effect of DCC and CS encapsulation on rat bone marrow stromal cells with the matrix synthesis boosted primarily by the inherently present extracellular matrix components. An important finding was that the cell seeded CS and DCC groups at week 6 had up to an order of magnitude higher glycosaminoglycan contents than their acellular counterparts. Gene expression results indicated a suppressive effect of DCC and CS encapsulation on rat bone marrow stromal cell chondrogenesis with differences in gene expression patterns existing between the DCC and CS groups. Overall, DCC and CS were easily included in microsphere-based scaffolds; however, there is a requirement to further refine their concentrations to achieve the differentiation profiles we seek in vitro.
Bone tissue engineering is an excellent alternative for the regeneration of large bone defects caused by trauma or bone pathologies. Scaffolds, stem cells, and bioactive molecules are the three key components of bone regeneration. Although a wide range of biomaterials of various compositions and structures has been proposed in the literature, these materials are rarely used in clinical applications. Therefore, more standardized studies are required to design scaffolds that enable better bone regeneration and are suitable for clinical use. The aim of this systematic review was to compare the performance of scaffolds used in preclinical animal studies to determine which class of materials has achieved a higher rate of bone neoformation (osteoinduction and osteoconduction). The selected studies were divided into three groups according to the following experimental models: studies that used subcutaneous models, bone defects in calvaria, and bone defects in long bones. Despite the large number of parameters in the included studies, we generally concluded that biomaterials containing calcium phosphates had important osteoinductive effects and were essential for better performance of the materials. Furthermore, natural polymers generally had better performance than synthetic polymers did, especially when the materials were associated with stem cells. The combination of materials from different classes was the most promising strategy for bone tissue regeneration.
To achieve tumor-specific delivery of doxorubicin, TiO2@Fe3O4/PEI/delivery of doxorubicin conjugates were designed and synthesized. Fe3O4 could act as magnetically responsive carriers and enhance the visible light photodynamic activities of TiO2. Delivery of doxorubicin was conjugated via coordination bond. The drug release rate at pH 5.2 was much faster than that at pH 7.4, due to pH-sensitive coordination bond. Besides, TiO2@Fe3O4/PEI/delivery of doxorubicin showed high antitumor efficacy combining with phototherapy, good bio-safety, higher cellular uptake with an external magnetic field, and less toxicity in vitro and in vivo. These results suggested that TiO2@Fe3O4/PEI/delivery of doxorubicin may be promising for high tumor treatment efficacy with minimal side effects in future.
The combination of patient-specific cells with scaffolds obtained from natural sources may result in improved regeneration of human tissues. Decellularization of the native tissue is the first step in this technology. Effective decellularization uses agents that lyse cells and remove all cellular materials, leaving intact collagenous extracellular matrices (ECMs). Removing cellular remnants prevents an immune response while preserving the underlying structure. In this study, the impact of five decellularization agents (0.1 N NaOH, 1% peracetic acid, 3% Triton X-100, 1% sodium dodecyl sulfate (SDS), and 0.05% trypsin/EDTA) on renal tissue was examined using slices of porcine kidneys. The NaOH solution induced the most efficient cell removal, and resulted in the highest amount of cell viability and proliferation after recellularization, although it also produced the most significant damage to collagenous fiber networks, glycosaminoglycans (GAGs) and fibroblast growth factor (FGF). The SDS solution led to less severe damage to the ECM structure but it resulted in lower metabolic activity and less proliferation. Peracetic acid and Triton X-100 resulted in minimum disruption of ECMs and the most preserved GAGs and FGF. However, these last two agents were not as efficient in removing cellular materials as NaOH and SDS, especially peracetic acid, which left more than 80% of cellular material within the ECM. As a proof of principle, after completing the comparison studies using slices of renal ECM, the NaOH process was used to decellularize a whole kidney, with good results. The overall results demonstrate the significant effect of cell lysing agents and the importance of developing an optimized protocol to avoid extensive damage to the ECM while retaining the ability to support cell growth.
Silk fibroin protein was purified from Bombyx mori silkworm cocoons using a novel dialysis strategy to avoid fibroin aggregation and pre-mature formation of β-sheets. The degummed silk fibers were dissolved in Ajisawa’s reagent, a mixture of CaCl2–EtOH–H2O, that is less expensive than lithium bromide. The dissolved solutions were dialyzed against either water or urea solution with a stepwise decrease in concentration. When the steps of 4 M-2 M-1 M-0 M urea (referred to as silk-TS-4210) were adopted, the purified silk fibroin had smaller aggregates (<10 nm), similar average molecular weight (225 kDa) and a lower content of β-sheet (~15%) compared to the sample processing methods (silk-TS-210, 10, 0) studied here. This outcome was close to the fibroin purified by the lithium bromide (silk-Li-0) method. Polyvinyl alcohol-emulsified silk microspheres generated using the purified solution had a similar size distribution and morphology when compared to lithium bromide dissolved solutions, while glycerol-blended silk films showed different mechanical properties. The silk-Li-0 generated films with the highest breaking strength (5.7 MPa ± 0.3) while the silk-TS-4210 had the highest extension at break (215.1% ± 12.5). The films prepared from silk-TS-4210 were cytocompatible to support the adhesion and proliferation of human mesenchymal stem cells, with improvements compared to the other samples likely due to the porous morphology of these films.
The clinical use of daunomycin is restricted by dose-dependent toxicity and low specificity against cancer cells. In the present study, modified superparamagnetic iron oxide nanoparticles were employed to load daunomycin and the drug-loaded nanospheres exhibited satisfactory size and smart pH-responsive release. The cellular uptake efficiency, targeted cell accumulation, and cell cytotoxicity experimental results proved that the superparamagnetic iron oxide nanoparticle-loading process brings high drug targeting without decreasing the cytotoxicity of daunomycin. Moreover, a new concern for the evaluation of nanophase drug delivery's effects was considered, with monitoring the interactions between human serum albumin and the drug-loaded nanospheres. Results from the multispectroscopic techniques and molecular modeling calculation elucidate that the drug delivery has detectable deleterious effects on the frame conformation of protein, which may affect its physiological function.
We fabricated a biodegradable antibiotic-eluting poly(
The pH-sensitive poly(D-A) grafted amine-functionalized bimodal mesoporous silica (D-A/BMMs) was prepared by a facile method used as a drug delivery vehicle. They exhibited superior properties such as good dispersion in aqueous medium, high drug loading efficiency, improved stability and high drug release rates. Meanwhile, its structural features and performances in a controlled delivery of ibuprofen (IBU) were systematically investigated by using XRD, N2 adsorption and desorption, SEM, TEM, FT-IR, elemental analysis and TG techniques. The results demonstrated that the obtained nanocomposite presented a flexible control over drug release by controlling the grafting amount of D-A onto the mesopores surface of aminated BMMs. The cumulative percent release of IBU from D-A/BMMs was found to be much higher at pH 7.4 than at pH 2.0. The release rate was very slow in an acidic medium but became faster in a neutral medium, owing to hydrogen bonding in an acidic medium and electrostatic repulsion between negatively charged carboxyl groups in an alkaline medium.
Infections after bone reconstructive surgery are a real therapeutic and economic issue for the modern health care system. As the pathogen (most often Staphylococcus aureus) is able to develop a biofilm inside the bone, local delivery of antibiotics is of interest since high drug concentrations would be delivered directly at the target place. In this context, this study evaluated a porous hydroxyapatite implant as biocompatible bone substitute and vancomycin-delivery system to prevent post-operative infections. A simple method of impregnation with optimised conditions insured a high antibiotic loading (up to 2.3 ± 0.3 mg/m2), with a complete in vitro release obtained within 1–5 days. Additionally, the bacteriostatic and bactericidal effects of vancomycin were retained after loading on hydroxyapatite, as demonstrated after challenge with a Staphylococcus aureus strain. Regarding the biocompatibility, a wound healing assay of pre-osteoblastic MC3T3-E1 cells exposed to various concentrations of vancomycin revealed a dose-dependent reduction in cell migration for antibiotic concentrations higher than 1 mg/mL. Meanwhile, cells were able to proliferate normally on vancomycin-loaded scaffolds, although cell initial adhesion was seriously impaired for scaffolds loaded with 2.3 mg/m2. Loaded scaffolds could be stored up to three months at room temperature without any degradation of the antibiotic. Together, these results demonstrate the efficacy of these hydroxyapatite bone substitutes for local delivery of vancomycin in the context of bone infection.
Biological function of adherent cells depends on the cell–cell and cell–matrix interactions in three-dimensional space. To understand the behavior of cells in 3D environment and their interactions with neighboring cells and matrix requires 3D culture systems. Here, we present a novel 3D cell carrier scaffold that provides an environment for routine 3D cell growth in vitro. We have developed thin, mechanically stable electrohydrodynamic jet (E-jet) 3D printed polycaprolactone and polycaprolactone/Chitosan macroporous scaffolds with precise fiber orientation for basic 3D cell culture application. We have evaluated the application of this technology by growing human embryonic stem cell-derived fibroblasts within these 3D scaffolds. Assessment of cell viability and proliferation of cells seeded on polycaprolactone and polycaprolactone/Chitosan 3D-scaffolds show that the human embryonic stem cell-derived fibroblasts could adhere and proliferate on the scaffolds over time. Further, using confocal microscopy we demonstrate the ability to use fluorescence-labelled cells that could be microscopically monitored in real-time. Hence, these 3D printed polycaprolactone and polycaprolactone/Chitosan scaffolds could be used as a cell carrier for in vitro 3D cell culture-, bioreactor- and tissue engineering-related applications in the future.
Aiming to mimic a blood vessel structurally, morphologically, and mechanically, a sequential electrospinning technique using a small diameter mandrel collector was performed and a three-layered tubular scaffold composed of nanofibers of polycaprolactone, collagen, and poly(
The bioactivity of yttrium and cerium are investigated when substituted for Sodium (Na) in a 0.52SiO2-0.24SrO-0.24-xNa2O-xMO glass-ceramics (where x = 0.08 and MO = Y2O3 or CeO2). Bioactivity is monitored through pH and inductively coupled plasma-optical emission spectrometry where pH of simulated body fluid ranged from 7.5 to 7.6 and increased between 8.2 and 10.0 after 14-day incubation with the glass-ceramic disks. Calcium (Ca) and phosphorus (P) levels in simulated body fluid after incubation with yttrium and cerium containing disks show a continual decline over the 14-day period. In contrast, Con disks (not containing yttrium or cerium) caused the elimination of Ca in solution after 1 day and throughout the incubation period, and initially showed a decline in P levels followed by an increase at 14 days. Scanning electron microscopy and energy dispersive spectroscopy confirmed the presence of Ca and P on the surface of the simulated body fluid-incubated disks and showed precipitates on Con and HCe (8 mol% cerium) samples. Cell viability of MC3T3 osteoblasts was not significantly affected at a 9% extract concentration. Optical microscopy after 24 h cell incubation with disks showed that Con samples do not support osteoblast or Schwann cell growth, while all yttrium and cerium containing disks have direct contact with osteoblasts spread across the wells. Schwann cells attached in all wells, but only showed spreading with the HY-S (8 mol% yttrium, heated to sintering temperature) and YCe (4 mol% yttrium and cerium) disks. Scanning electron microscopy of the compatible disks shows osteoblast and sNF96.2 Schwann cells attachment and spreading directly on the disk surfaces.
The possibility of genipin-crosslinked O-carboxymethyl chitosan–gum Arabic coacervate as a pH-sensitive delivery vehicle was investigated. O-carboxymethyl chitosan–gum Arabic coacervates separated in pH 3.0, 4.5, and 6.0 were crosslinked by genipin for different durations and the crosslinked products were subjected to crosslinking degree, swelling behavior, bovine serum albumin release profile, and microstructure characterization. Genipin-crosslinking greatly improved the stability of the coacervates against the simulated gastric solution and created certain pH-sensitivity. The coacervates displayed higher swelling ratios in the simulated gastric solution than in the simulated intestine and colon solutions; meanwhile, the coacervates prepared in pH 4.5 and 6.0 swelled more severely than the complex separated in pH 3.0. Nevertheless, the bovine serum albumin release in the simulated gastric solution from the microcapsules prepared in pH 6.0 was much lower than those prepared in pH 4.5 and 3.0, whose cumulative release percentages in the three simulated solutions were 17.14%, 55.23%, and 79.79%, respectively, in crosslinking duration 2 h. X-ray diffraction, scanning electron microscopy, and transmission electron microscopy analysis revealed that genipin-crosslinking improved the regularity and compactness of coacervate structure, whereas confocal laser scanning microscopy observation indicated that O-carboxymethyl chitosan content was possibly the major reason for the different swelling and bovine serum albumin release behavior of the coacervates. It was concluded that the genipin-crosslinked O-carboxymethyl chitosan–gum Arabic coacervate was a potential intestine-targeted delivery system and its delivery performance could be tailored by varying the crosslinking degree and coacervation acidity.
Delivery of amphiphobic drugs (insoluble in both water and oil) has been a great challenge in drug delivery. SNX-2112, a novel inhibitor of Hsp90, is a promising drug candidate for treating various types of cancers; however, the insolubility greatly limits its clinical application. This study aimed to build a new type of drug delivery system using single-walled carbon nanotubes (SWNTs) for controllable release of SNX-2112; chitosan (CHI) was non-covalently added to SWNTs to improve their biocompatibility. SWNTs-CHI demonstrated high drug-loading capability; the release of SNX-2112 was pH triggered and time related. The intracellular reactive oxygen species of SWNTs–CHI increased, compared with that of SWNTs, leading to higher mitogen-activated protein kinase and cell apoptosis. The results of western-blotting, lactate dehydrogenase (LDH) release assay, and cell viability assay analyses indicated that apoptosis-related proteins were abundantly expressed in K562 cells and that the drug delivery system significantly inhibited K562 cells. Thus, SWNT–CHI/SNX-2112 shows great potential as a drug delivery system for cancer therapy.
In this study, disruption and lyophilization–rehydration of dopamine-loaded liposome and its application in electrochemical DNA biosensor was investigated. The liposomes containing soyphosphatidylcholine and cholesterol were prepared through thin-layer hydration. First, an investigation was carried out to find an appropriate lysing agent for disruption of prepared liposomes. Differential pulse voltammetry, as a high sensitive electrochemical technique, was used along with a multi-walled carbon nanotubes modified glassy carbon electrode for sensitive electrochemical detection of released dopamine from disrupted liposomes. Various lysing agents were investigated and finally, the disruption of liposomes using methanol was selected without any surfactant, because of its least fouling effect. Then, lyophilization of dopamine-loaded liposomes was carried out using sucrose as cryoprotectant. The electrochemical studies of lyophilized liposomes showed that the remained dopamine in sucrose-protected liposomes was higher than sucrose-free liposomes. Furthermore, sucrose has no interference in electrochemical studies. Then, with the addition of biotin-X-DHPE to liposome formulation, the lyophilized sucrose protected dopamine-loaded biotin-tagged liposomes were prepared and the feasibility of application of them in electrochemical DNA biosensor was investigated as signal enhancer and verified for detection of oligonucleotides.
There is a need to develop pro-angiogenic biomaterials to promote wound healing and to assist in regenerative medicine. To this end, various growth factors have been exploited which have the potential to promote angiogenesis. However, these are generally expensive and labile which limits their effectiveness. An alternative approach is to immobilize heparin onto biocompatible degradable hydrogels. The heparin in turn will then bind endogenous proangiogenic growth factors to induce formation of new blood vessels.
In this study, we continue our development of hydrogels for wound healing purposes by exploring covalently cross-linking chitosan and polyvinyl alcohol hydrogels using triethyl orthoformate. Two concentrations of triethyl orthoformate (4 and 16%) were compared for their effects on the structure of hydrogels – their swelling, pore size, and rate of degradation and for their ability to support the growth of cells and for their heparin-binding capacity and their effects on angiogenesis in a chick chorioallantoic membrane assay.
Hydrogels formed with 4 or 16% both triethyl orthoformate cross-linker were equally cyto-compatible. Hydrogels formed with 4% triethyl orthoformate absorbed slightly more water than those made with 16% triethyl orthoformate and broke down slightly faster than non-cross-linked hydrogels. When soaked in heparin the hydrogel formed with 16% triethyl orthoformate showed more blood vessel formation in the CAM assay than that formed with 4% triethyl orthoformate.
Hyaluronic acid (HAc)–hydroxyapatite (HAp) composite hydrogels were developed to improve the biostability and bioactivity of HAc for dermal filler applications. Two kinds of HAc-HAp composite fillers were generated: HAcmicroHAp and HAc-nanoHAp composites. HAc-microHAp was fabricated by mixing HAp microspheres with HAc hydrogels, and HAc-nanoHAp was made by in situ precipitation of nano-sized HAp particles in HAc hydrogels. Emphasis was placed on the effect of HAp on the durability and bioactivity of the fillers. Compared with the pure HAc filler, all of the HAc-HAp composite fillers exhibited significant improvements in volumetric maintenance based on in vivo tests owing to their reduced water content and higher degree of biointegration between the filler and surrounding tissues. HAc-HAp composite fillers also showed noticeable enhancement in dermis recovery, promoting collagen and elastic fiber formation. Based on their long-lasting durability and bioactivity, HAc-HAp composite fillers have great potential for soft tissue augmentation with multifunctionality.
In the present study, alginate nanoparticles were firstly prepared for paclitaxel (PTX) delivery with an average size of 200 ± 21 nm. To improve the stability and targeting effect, the chitosan (CS) and folate-chitosan (FA-CS) were introduced to form PTX-loaded CS/ALG NPs and FA-CS/ALG NPs by a new double emulsion cross-linking electrostatic attraction method. The optimization chitosan concentration was 0.5% obtained from the experiment results. The CS/ALG-PTX NPs and FA-CS/ALG-PTX NPs had the average particle size of 306.9 ± 12.9 nm and 283.6 ± 19.2 nm with the zeta potential of 31.1 ± 1.3 mV and –2.98 ± 0.7 mV, and had higher drug loading and entrapment efficiencies than ALG-PTX NPs. The in vitro drug release profile along with release kinetics and mechanism from PTX-loaded NPs were studied under two simulated physiological conditions. Further, the in vitro anti-cancer activity of nanoparticles and the cellular uptake of nanoparticles on HepG2 cells were investigated. The results demonstrated that alginate, CS/ALG and FA-CS/ALG can be used as nanoformulation drug carriers by our new method, and FA-CS/ALG was a promising vehicle for anticancer drug targeted delivery system.
Excessive demineralization in osteoporotic bones impairs its self-regeneration potential following a defect/fracture and is of great concern among the aged population. In this context, implants with inherent osteogenic ability loaded with therapeutic ions like Strontium (Sr2+) may bring forth promising outcomes. Micro-granular Strontium incorporated Hydroxyapatite scaffolds have been synthesized and in vivo osteogenic efficacy was evaluated in a long-term osteoporosis-induced aged (LOA) rat model. Micro-granules with improved surface area are anticipated to resorb faster and together with the inherent bioactive properties of Hydroxyapatite with the leaching of Strontium ions from the scaffold, osteoporotic bone healing may be promoted. Long-term osteoporosis-induced aged rat model was chosen to extrapolate the results to clinical osteoporotic condition in the aged. Micro-granular 10% Strontium incorporated Hydroxyapatite synthesized by wet precipitation method exhibited increased in vitro dissolution rate and inductively coupled plasma studies confirmed Strontium ion release of 0.01 mM, proving its therapeutic potential for osteoporotic applications. Wistar rats were induced to long-term osteoporosis-induced aged model by ovariectomy along with a prolonged induction period of 10 months. Thereafter, osteogenic efficacy of Strontium incorporated Hydroxyapatite micro-granules was evaluated in femoral bone defects in the long-term osteoporosis-induced aged model. Post eight weeks of implantation in vivo regeneration efficacy ratio was highest in the Strontium incorporated Hydroxyapatite implanted group (0.92 ± 0.04) compared to sham and Hydroxyapatite implanted group. Micro CT evaluation further substantiated the improved osteointegration of Strontium incorporated Hydroxyapatite implants from the density histograms. Thus, the therapeutical potential of micro-granular Strontium incorporated Hydroxyapatite scaffolds becomes relevant, especially as bone void fillers in osteoporotic cases of tumor resection or trauma.
The objective of this study was to develop a bimetallic nanoparticle with enhanced antibacterial activity that would improve the therapeutic efficacy against bacterial biofilms. Bimetallic gold–silver nanoparticles were bacteriogenically synthesized using -proteobacterium, Shewanella oneidensis MR-1. The antibacterial activities of gold–silver nanoparticles were assessed on the planktonic and biofilm phases of individual and mixed multi-cultures of pathogenic Gram negative (Escherichia coli and Pseudomonas aeruginosa) and Gram positive bacteria (Enterococcus faecalis and Staphylococcus aureus), respectively. The minimum inhibitory concentration of gold–silver nanoparticles was 30–50 µM than that of other nanoparticles (>100 µM) for the tested bacteria. Interestingly, gold–silver nanoparticles were more effective in inhibiting bacterial biofilm formation at 10 µM concentration. Both scanning and transmission electron microscopy results further accounted the impact of gold–silver nanoparticles on biocompatibility and bactericidal effect that the small size and bio-organic materials covering on gold–silver nanoparticles improves the internalization and thus caused bacterial inactivation. Thus, bacteriogenically synthesized gold–silver nanoparticles appear to be a promising nanoantibiotic for overcoming the bacterial resistance in the established bacterial biofilms.
A bioactive glass series (0.42SiO2-0.10Na2O-0.08CaO-(0.40–x)ZnO-(x)Ga2O3) was incorporated in carboxymethyl cellulose–dextran hydrogels at three different loadings (0.05, 0.10, and 0.25 m2), and the resulting composites were characterized using scanning electron microscopy, physical swelling characteristics, and inductively coupled plasma optical emission spectroscopy. In vitro cytocompatibility was also evaluated for composite extracts in contact with L-929 mouse fibroblasts and MC3T3-E1 human osteoblasts. Scanning electron microscopy confirmed that glass particles were distributed throughout the hydrogels, and swelling studies showed that glass presence can increase the amount of fluid that can be absorbed by the hydrogels after seven days of immersion in phosphate-buffered saline by up to 180%. Several trends were observed in the inductively coupled plasma optical emission spectroscopy data, with the most important being the release of Ga3+ from both Ga-containing glasses at all three loadings, with a maximum of 4.7 mg/L released after 30 days of incubation in phosphate-buffered saline. Cell viability analysis suggested that most composite extracts did not decrease neither fibroblast nor osteoblast viability. These results indicate that it is possible to embed bioactive glass particles into carboxymethyl cellulose–dextran hydrogels, and upon submersion in aqueous media, release ions from the glass particles that may elicit therapeutic effects.
Polypropylene mesh, as a temporary abdominal closure device, may cause mechanical intestine injury and inflammatory response. Chitosan/gelatin hydrogel has excellent biocompatibility, soft and elastic properties. This work is to assess the effects of the chitosan/gelatin hydrogel coated polypropylene mesh on open abdomen wounds. Histological analysis and detection of healing-related factors were conducted to evaluate the inflammation and wound healing process. After 1-day implantation in a murine model of open abdomen, the coated polypropylene mesh, compared with simple polypropylene mesh, demonstrated well protection of the intestine serosa. After 14-day implantation, it reduced the inflammation response by down-regulating the cytokines interleukin-6 and tumor necrosis factor-α, and up-regulating the anti-inflammatory factor interleukin-10. Meanwhile, the composite stimulated granulation tissue growth, and promoted matrix deposition and angiogenesis after 7 and 14 days. In conclusion, the modified temporary abdominal closure composite could significantly protect the intestines from mechanical damage and accelerate wound healing.
Titanium implants possessing excellent antibacterial activity are highly desirable for the prevention of implant-associated infections. In this study, we demonstrate a simple one-step, water-based procedure for the fabrication of biofunctionalized nanocomposites on titanium for implant application. The formation of biofunctionalized silver nanoparticles with varied biomolecule templates is confirmed by Fourier-transform infrared spectroscopic, contact angle, field-emission scanning electron microscopy, and inductively coupled plasma atomic emission spectrometry analysis. Antibacterial properties of the specimens were determined by challenging them against Staphylococcus aureus. The Ag-incorporated titanium shows excellent antibacterial ability against planktonic bacteria in the suspension and ability to prevent bacterial adhesion. The specimens with optimized biomolecule/silver ratio promote osteoblast differentiation. These biofunctionalized silver nanoparticles-doped titanium specimens, with improved antibacterial activity while maintaining healthy osteoblast cellular activity, have promising application in orthopedics, dentistry, and other biomedical devices.
Sodium alginate is an effective biomaterial for tissue engineering applications. Non-purified alginate is contaminated with protein, lipopolysaccharide, DNA, and RNA, which could elicit adverse immunological reactions. We developed a purification protocol to generate biocompatible alginate based on (a) activated charcoal treatment, (b) use of hydrophobic membrane filtration (we used hydrophobic polyvinylidene difluoride membranes to remove organic contaminants), (c) dialysis, and finally (d) ethanol precipitation. Using this approach, we could omit pre-treatment with chloroform and significantly reduce the quantities of reagents used. Purification resulted in reduction of residual protein by 70% down to 0.315 mg/g, DNA by 62% down to 1.28 µg/g, and RNA by 61% down to less than 10 µg/g, respectively. Lipopolysaccharide levels were reduced by >90% to less than 125 EU/g. Purified alginate did not induce splenocyte proliferation in vitro. Three-dimensional scaffolds generated from purified alginate did not elicit a significant foreign body reaction, fibrotic overgrowth, or macrophage infiltration 4 weeks after implantation. This study describes a simplified and economical alginate purification method that results in alginate purity, which meets clinically useful criteria.
In this study, nanocomposite collagen scaffolds incorporating gold nanoparticles (AuNPs) were prepared for wound healing applications. Initially, dose (<20 ppm) and size (>20 nm) of AuNPs that were not cytotoxic on HaCat keratinocytes and 3T3 fibroblasts were determined. Both collagen sponges and AuNP-incorporated nanocomposites (CS-Au) were cross-linked with glutaraldehyde (CS-X and CS-AuX). Incorporation of AuNPs into cross-linked scaffolds enhanced their stability against enzymatic degradation and increased the tensile strength. Hydrolytic degradation of CS-Au group was also less than CS after seven days. Upon confirming in vitro biocompatibility of the scaffolds with cytotoxicity assays, cell attachment and proliferation tests and the in vivo efficacy for healing of full-thickness skin wounds were investigated by applying CS-X, CS-AuX or a commercial product (Matriderm®) onto defect sites and covering with Ioban® drapes. Defects were covered only with drapes for untreated control group. The wound areas were examined with histopathological and biomechanical tests after 14 days of operation. CS-AuX group was superior to untreated control and Matriderm®; it suppressed the inflammation while significantly promoting granulation tissue formation. Inflammatory reaction against CS-AuX was milder than CS-X. Neovascularization was also higher in CS-AuX than other groups, though the result was not significant. Wound closure in CS-X (76%), CS-AuX (69%), and Matriderm® (65%) were better than untreated control (45%). CS-AuX group had the highest tensile strength (significantly higher than Matriderm®) and modulus (significantly higher than Matriderm® and CS-X), indicating a faster course of dermal healing. Further studies are also needed to investigate whether higher loading of AuNPs affects these results positively in a statistically meaningful manner. Overall, their contribution to the enhancement of degradation profiles and mechanical properties, their excellent in vitro biocompatibility, and tendency to accelerate wound healing are encouraging the use of AuNPs in collagen sponges as potent skin substitutes in the future.
Physico-chemical and mechanical properties of hyaluronic acid/carbon nanotubes nanohybrids have been correlated with the proportion of inorganic nanophase and the preparation procedure. The mass fraction of -COOH functionalized carbon nanotubes was varied from 0 to 0.05. Hyaluronic acid was crosslinked with divinyl sulfone to improve its stability in aqueous media and allow its handling as a hydrogel. A series of samples was dried by lyophilization to obtain porous scaffolds whereas another was room-dried allowing the collapse of the hybrid structures. The porosity of the former, together with the tighter packing of hyaluronic acid chains, results in a lower water absorption and lower mechanical properties in the swollen state, because of the easier water diffusion. The presence of even a small amount of carbon nanotubes (mass fraction of 0.05) limits even more the swelling of the matrix, owing probably to hybrid interactions. These nanohybrids do not seem to degrade significantly during 14 days in water or enzymatic medium.
Mesenchymal stem cells have shown great potential for accelerating bone healing. In the present study, we evaluate the efficacy of fibrin glue/mesenchymal stem cells/recombinant human bone morphogenetic protein-2 composite for posterolateral spinal fusion in a rabbit model. Forty adult rabbits underwent posterolateral intertransverse fusion at the L5–L6 level. The animals were randomly divided into four groups based on the implant material: fibrin glue, fibrin glue/mesenchymal stem cells composite, fibrin glue-recombinant human bone morphogenetic protein-2 (fibrin glue/recombinant human bone morphogenetic protein-2) composite, and fibrin glue/mesenchymal stem cells/recombinant human bone morphogenetic protein-2 composite. After six weeks, the rabbits were euthanized for manual palpation, radiographic examination, biomechanical testing, and histology. Manual palpation results showed that the fusion rate for fibrin glue, fibrin glue/mesenchymal stem cells, fibrin glue/recombinant human bone morphogenetic protein-2, and fibrin glue/mesenchymal stem cells/recombinant human bone morphogenetic protein-2 was 0, 0, 40%, and 70%, respectively. Moreover, fusion rate determined by radiographic examination for fibrin glue, fibrin glue/mesenchymal stem cells, fibrin glue/recombinant human bone morphogenetic protein-2, and fibrin glue/mesenchymal stem cells/recombinant human bone morphogenetic protein-2 was 0, 0, 40%, and 80%, respectively. Gray analysis showed that fibrin glue/recombinant human bone morphogenetic protein-2 group had higher ossification area and density than fibrin glue group; and fibrin glue/mesenchymal stem cells/recombinant human bone morphogenetic protein-2 group had higher ossification area and density than fibrin glue/recombinant human bone morphogenetic protein-2 group. Formation of continuous bone masses between L5 and L6 level in mesenchymal stem cells/recombinant human bone morphogenetic protein-2/fibrin glue group was further confirmed by computed tomography scanning and three-dimensional reconstruction. Biomechanical testing demonstrated that the fusion strength (flexion, extension, lateral bending, and axial rotation) in fibrin glue/mesenchymal stem cells/recombinant human bone morphogenetic protein-2 group is significantly higher than that in fibrin glue/recombinant human bone morphogenetic protein-2 group. The formation of mature bone tissues between transverse processes of the fused specimens from both fibrin glue/recombinant human bone morphogenetic protein-2, and fibrin glue/mesenchymal stem cells/recombinant human bone morphogenetic protein-2 groups was confirmed by HE staining, and quantitative real-time polymerase chain reaction results showed the upregulation of CD31, type I collagen, osteocalcin, and osteonectin in the fibrin glue/mesenchymal stem cells/recombinant human bone morphogenetic protein-2 group. In conclusion, our findings show that mesenchymal stem cells delivered with recombinant human bone morphogenetic protein-2 using fibrin glue as carrier are more effective in enhancing spine fusion than recombinant human bone morphogenetic protein-2 without mesenchymal stem cells in the rabbit model.
This work presents a new series of polycationic nanoparticles of (l-)-lysine conjugated amphiphilic triblock copolymer poly(hydroxyletheyl methacrylate-L-lysine)-b-poly(L-lactide)-b-poly(hydroxyletheyl methacrylate-L-lysine)s (PHML-b-PLLA-b-PHML) as potent low cytotoxic vectors for intracellular plasmid DNA delivery. First, the triblock PHML-b-PLLA-b-PHML copolymers were prepared via a combination of metal-free controlled ring opening polymerization and successive atom transfer radical polymerization. Then the cationic PHML-b-PLLA-b-PHML nanoparticles were further prepared by solution self-assembly. The particle size, zeta potential and morphology of as-prepared PHML-b-PLLA-b-PHML nanoparticles were characterized by dynamic light scattering and atomic force microscopy, respectively. The plasmid DNA binding affinities and polyplex stabilities were separately explored by agarose gel retardation and DNase I degradation assays. Then in vitro cytotoxicity and gene transfection efficiency of the PHML-b-PLLA-b-PHML nanoparticles vectors as well as relevant polyplex endocytosis pathway were investigated with H1299 cells. It was revealed that the PHML-b-PLLA-b-PHML nanoparticles exhibited low cytotoxicity, strong plasmid DNA binding affinity, high polyplex stability and efficient plasmid DNA transfection even under serum conditions (10% FBS). Moreover, the endocytosis analysis results disclosed that the PHML30-b-PLLA-b-PHML30 nanoparticle/plasmid DNA polyplexes were predominantly involved in lipid-raft-mediated endocytosis pathway, similar to that of SV40 virus-based vectors.
Arsenic trioxide (As2O3, ATO), a FDA approved drug for hematologic malignancies, was proved of efficient growth inhibition of cancer cell in vitro or solid tumor in vivo. However, its effect on solid tumor in vivo was hampered by its poor pharmacokinetics and dose-limited toxicity. In this study, a polyacrylic acid capped pH-triggered mesoporous silica nanoparticles was conducted to improve the pharmacokinetics and enhance the antitumor effect of arsenic trioxide. The mesoporous silica nanoparticles loaded with arsenic trioxide was grafted with polyacrylic acid (PAA-ATO-MSN) as a pH-responsive biomaterial on the surface to achieve the release of drug in acidic microenvironment of tumor, instead of burst release action in circulation. The nanoparticles were characterized with uniform grain size (particle sizes of 158.6 ± 1.3 nm and pore sizes of 3.71 nm, respectively), historically comparable drug loading efficiency (11.42 ± 1.75%), pH-responsive and strengthened sustained release features. The cell toxicity of amino groups modified mesoporous silica nanoparticles (NH2-MSN) was significantly reduced by capping of polyacrylic acid. In pharmacokinetic studies, the half time (t1/2β) was prolonged by 1.3 times, and the area under curve) was increased by 2.6 times in PAA-ATO-MSN group compared with free arsenic trioxide group. Subsequently, the antitumor efficacy in vitro (SMMC-7721 cell line) and in vivo (H22 xenografts) was remarkably enhanced indicated that PAA-ATO-MSN improved the antitumor effect of the drug. These results suggest that the polyacrylic acid capped mesoporous silica nanoparticles (PAA-MSN) will be a promising nanocarrier for improving pharmacokinetic features and enhancing the anti-tumor efficacy of arsenic trioxide.
Chronic osteomyelitis is difficult to be cured and often relapses, which presents to be a great challenge to clinicians. We conducted this original study to explore the efficiency of therapeutic alliance for chronic osteomyelitis by a multi-drug implant based on three-dimensional printing technology. We designed and fabricated preciously a multi-drug implant with a multi-layered concentric cylinder construction by three-dimensional (3D) printing technology. Levofloxacin and tobramycin were incorporated into the drug implant in a specific sequence. The drug release property of the drug implant was assayed in vitro. We also developed an animal model of chronic osteomyelitis to estimate the effect of the 3D printed multi-drug implant. The results showed that the multi-drug implant had a sustained and programmed drug release property. Levofloxacin and tobramycin which were released from the multi-drug implant worked in tandem to enhance pharmacodynamic action which was similar to a tumor chemotherapy program and were sufficient to treat chronic osteomyelitis. These findings imply that the administration of 3D printed multi-drug implant would be a potential therapeutic method for chronic osteomyelitis. Further studies are required.
Articular cartilage defects, when repaired ineffectively, often lead to further deterioration of the tissue, secondary osteoarthritis and, ultimately, joint replacement. Unfortunately, current surgical procedures are unable to restore normal cartilage function. Tissue engineering of cartilage provides promising strategies for the regeneration of damaged articular cartilage. As yet, there are still significant challenges that need to be overcome to match the long-term mechanical stability and durability of native cartilage. Using electrospinning of different blends of biodegradable poly(3-hydroxybutyrate)/poly(3-hydroxyoctanoate), we produced polymer scaffolds and optimised their structure, stiffness, degradation rates and biocompatibility. Scaffolds with a poly(3-hydroxybutyrate)/poly(3-hydroxyoctanoate) ratio of 1:0.25 exhibit randomly oriented fibres that closely mimic the collagen fibrillar meshwork of native cartilage and match the stiffness of native articular cartilage. Degradation of the scaffolds into products that could be easily removed from the body was indicated by changes in fibre structure, loss of molecular weight and a decrease in scaffold stiffness after one and four months. Histological and immunohistochemical analysis after three weeks of culture with human articular chondrocytes revealed a hyaline-like cartilage matrix. The ability to fine tune the ultrastructure and mechanical properties using different blends of poly(3-hydroxybutyrate)/poly(3-hydroxyoctanoate) allows to produce a cartilage repair kit for clinical use to reduce the risk of developing secondary osteoarthritis. We further suggest the development of a toolbox with tailor-made scaffolds for the repair of other tissues that require a ‘guiding’ structure to support the body’s self-healing process.
Re-establishing compromised periodontium to its original structure, properties and function is demanding, but also challenging, for successful orthodontic treatment. In this study, the periodontal regeneration capability of collagen-hydroxyapatite scaffolds, seeded with bone marrow stem cells, was investigated in a canine labial alveolar bone defect model. Bone marrow stem cells were isolated, expanded and characterized. Porous collagen-hydroxyapatite scaffold and cross-linked collagen-hydroxyapatite scaffold were prepared. Attachment, migration, proliferation and morphology of bone marrow stem cells, co-cultured with porous collagen-hydroxyapatite or cross-linked collagen-hydroxyapatite, were evaluated in vitro. The periodontal regeneration capability of collagen-hydroxyapatite scaffold with or without bone marrow stem cells was tested in six beagle dogs, with each dog carrying one sham-operated site as healthy control, and three labial alveolar bone defects untreated to allow natural healing, treated with bone marrow stem cells – collagen-hydroxyapatite scaffold implant or collagen-hydroxyapatite scaffold implant, respectively. Animals were euthanized at 3 and 6 months (3 animals per group) after implantation and the resected maxillary and mandibular segments were examined using micro-computed tomography scan, H&E staining, Masson's staining and histometric evaluation. Bone marrow stem cells were successfully isolated and demonstrated self-renewal and multi-potency in vitro. The porous collagen-hydroxyapatite and cross-linked collagen-hydroxyapatite had average pore sizes of 415 ± 20 µm and 203 ± 18 µm and porosity of 69 ± 0.5% and 50 ± 0.2%, respectively. The attachment, proliferation and migration of bone marrow stem cells were satisfactory on both porous collagen-hydroxyapatite and cross-linked collagen-hydroxyapatite scaffolds. Implantation of bone marrow stem cells – collagen-hydroxyapatite or collagen-hydroxyapatite scaffold in beagle dogs with experimental periodontal defects resulted in significantly enhanced periodontal regeneration characterized by formation of new bone, periodontal ligament and cementum, compared with the untreated defects, as evidenced by histological and micro-computed tomography examinations. The prepared collagen-hydroxyapatite scaffolds possess favorable bio-compatibility. The bone marrow stem cells – collagen-hydroxyapatite and collagen-hydroxyapatite scaffold – induced periodontal regeneration, with no aberrant events complicating the regenerative process. Further research is necessary to improve the bone marrow stem cells behavior in collagen-hydroxyapatite scaffolds after implantation.
In our previous work, we have developed an effective microcavitary alginate hydrogel for proliferation of chondrocytes and maintenance of chondrocytic phenotype. In present work, we investigated whether microcavitary alginate hydrogel could promote the chondrogenesis of progenitor cells. Moreover, we attempted to further optimize this system by incorporating synthetic Arg-Gly-Asp peptide. ATDC5 cells were seeded into microcavitary alginate hydrogel with or without Arg-Gly-Asp immobilization. Cell Counting Kit-8 and live/dead staining were conducted to analyze cell proliferation. Real-time polymerase chain reaction (RT-PCR), hematoxylin and eosin, and Toluidine blue O staining as well as Western blot assay was performed to evaluate the cartilaginous markers at transcriptional level and at protein level, respectively. The obtained data demonstrated that Arg-Gly-Asp-immobilized microcavitary alginate hydrogel was preferable to promote the cell proliferation. Also, Arg-Gly-Asp-immobilized microcavitary alginate hydrogel improved the expression of chondrocytic genes including Collagen II and Aggrecan when compared with microcavitary alginate hydrogel. The results suggested that microcavitary alginate hydrogel could promote the chondrogenesis. And Arg-Gly-Asp would be promising to ameliorate this culture system for cartilage tissue engineering.
Polyetheretherketone (PEEK) is a bioinert thermoplastic that has been investigated for its potential use in craniofacial reconstruction; however, its use in clinical practice is limited by a poor integration with adjacent bone upon implantation. To improve the bone–implant interface, two strategies have been employed: to modify its surface or to impregnate PEEK with bioactive materials. This study attempts to combine and improve upon the two approaches by modifying the internal structure into a trabecular network and to impregnate PEEK with mesenchymal stem cells. Furthermore, we compare the newly designed PEEK scaffolds' interactions with both bone-derived (BMSC) and adipose (ADSC) stem cells.
Customized PEEK scaffolds were designed to incorporate a trabecular microstructure using a computer-aided design program and then printed via selective laser sintering (SLS), a 3D-printing process with exceptional accuracy. The scaffold structure was evaluated using microCT. Scanning electron microscopy (SEM) was used to evaluate scaffold morphology with and without mesenchymal stem cells (MSCs). Adipose and bone marrow mesenchymal cells were isolated from rats and cultured on scaffolds. Cell proliferation and differentiation were assessed using alamarBlue and alkaline phosphatase assays, respectively. Cell morphology after one week of co-culturing cells with PEEK scaffolds was evaluated using SEM.
SLS 3D printing fabricated scaffolds with a porosity of 36.38% ± 6.66 and density of 1.309 g/cm2. Cell morphology resembled viable fibroblasts attaching to the surface and micropores of the scaffold. PEEK scaffolds maintained the viability of both ADSCs and BMSCs; however, ADSCs demonstrated higher osteodifferentiation than BMSCs (p < 0.05).
This study demonstrates for the first time that SLS 3D printing can be used to fabricate customized porous PEEK scaffolds that maintain the viability of adipose and bone marrow-derived MSCs and induce the osteodifferentiation of the adipose-derived MSCs. The combination of 3D printed PEEK scaffolds with MSCs could overcome some of the limitations using PEEK biopolymers for load-bearing bone regeneration in craniofacial reconstruction.
Posterior capsular opacification (PCO) is a common complication in cataract surgery. The development of PCO is attributed to the combination of adhesion, migration, proliferation, and transdifferentiation of the residual lens epithelial cells (LEC) onto the interface of intraocular lens (IOL) material and lens posterior, in which the initial adhesion is the beginning step and plays important roles. In the present study, hydrophilic polyethylene glycol (PEG) was immobilized onto IOL surface via plasma-aided chemical grafting procedure. The attenuated total reflection – Fourier transform infrared (ATR-FTIR) and contact angle (CA) – measurements indicate the successful surface PEGylation, as well as the excellent hydrophilicity of the surfaces. Compared with pristine IOL, the PEGylation does not influent its optical property, whereas the initial adhesion of LEC is greatly inhibited. In vivo ocular implantation results show that the PEGylated IOL presents good in vivo biocompatibility, and can effectively prevent the PCO development.
The biological and mechanical nature of calcium phosphate cements (CPC's) matches well with that of bone tissues, thus they can be considered as an appropriate environment for bone repair as bone defect fillers. The current study focuses on the experimental characterization of the mechanical properties of CPCs that are favorably used in clinical applications. Aiming on evaluation of their mechanical performance, tests in compression loading were conducted in order to determine the mechanical properties of the material under study. In this context, experimental results occurring from the above mechanical tests on porous specimens that were fabricated from three different porous additives, namely albumin, gelatin and sodium alginate, are provided, while assessment of their mechanical properties in respect to the used porous media is performed. Additionally, samples reinforced with hydroxyapatite crystals were also tested in compression and the results are compared with those of the above tested porous CPCs. The knowledge obtained allows the improvement of their biomechanical properties by controlling their structure in a micro level, and finds a way to compromise between mechanical and biological response.
A series biodegradable poly (-glutamic acid)/beta-tricalcium phosphate (-PGA/TCP) nanocomposites were prepared which were composed of poly--glutamic acid polymerized in situ with β-tricalcium phosphate and physiochemically characterized as bone graft substitutes. The particle size via dynamic light scattering, the direct morphological characterization via transmission electron microscopy and field emission scanning electron microscope, which showed that -PGA and β-TCP were combined compactly at 80℃, and the -PGA/TCP nanocomposites had homogenous and nano-sized grains with narrow particle size distributions. The water uptake and retention abilities, in vitro degradation properties, cytotoxicity in the simulated medium, and protein release of these novel -PGA/TCP composites were investigated. Cell proliferation in composites was nearly twice than β-TCP when checked in vitro using MC3T3 cell line. We also envision the potential use of -PGA/TCP systems in bone growth factor or orthopedic drug delivery applications in future bone tissue engineering applications. These observations suggest that the -PGA/TCP are novel nanocomposites with great potential for application in the field of bone tissue engineering.
In this study, we reported the preparation of self cross-linked oxidized alginate–gelatin hydrogels for muscle tissue engineering. The effect of oxidation degree (OD) and oxidized alginate/gelatin (OA/GEL) weight ratio were examined and the results showed that in the constant OA/GEL weight ratio, both cross-linking density and Young’s modulus enhanced by increasing OD due to increment of aldehyde groups. Furthermore, the degradation rate was increased with increasing OD probably due to decrement in alginate molecular weight during oxidation reaction facilitated degradation of alginate chains. MTT cytotoxicity assays performed on Wharton's Jelly-derived umbilical cord mesenchymal stem cells cultured on hydrogels with OD of 30% showed that the highest rate of cell proliferation belong to hydrogel with OA/GEL weight ratio of 30/70. Overall, it can be concluded from all obtained results that the prepared hydrogel with OA/GEL weight ratio and OD of 30/70 and 30%, respectively, could be proper candidate for use in muscle tissue engineering.
The present study aims to investigate the contribution of two biologically important cations, Mg2+ and Sr2+, when co-substituted into the structure of hydroxyapatite (Ca10(PO4)6(OH)2, HA). The substituted samples were synthesized by a hydrothermal method that involved the addition of Mg2+ and Sr2+ containing precursors to partially replace Ca2+ in the apatite structure. Four co-substituted HA samples with different concentrations of Mg2+ and Sr2+ ((Mg + Sr)/(Mg + Sr + Ca) = 30%) were investigated, and they were compared with pure HA. Experimental results showed that only a limited amount of Mg (Mg/(Mg + Ca + Sr) < 14%) could successfully substitute for Ca in HA. In addition, Mg substitution resulted in reduced crystallinity, thermal stability and lattice parameters of HA. In contrast, Sr could fully substitute for Ca. Furthermore, the addition of Sr increased the lattice parameters of HA. Here, we obtained the cation leach liquor by immersing the prepared samples in a culture medium for cell experiments. The in vitro study showed that 10Mg20Sr promoted better MG63 cell attachment, proliferation and differentiation than HA. Thus, the presence of an appropriate proportion of Mg and Sr could play a significant role in the increased biocompatibility of HA.
Phenylalanine ethyl ester (PAE)–alginate (Alg) conjugate (PAE–Alg, PEA) was synthesized and formation of an amide bond between PAE and Alg was confirmed by Fourier transformed-infrared and 1H nuclear magnetic resonance spectroscopy. The degree of PAE substitution was 3.5–4.7 (PAE group per hundred sugar residues of Alg) which was determined by elemental analysis. The critical aggregation concentration values determined for PEA conjugates PEA1, PEA2, and PEA3 were 0.20, 0.12, and 0.10 mg/ml, respectively. The particle size of PEA nanoparticles (PEA-NPs) decreased from 425 nm to 226 nm with the increasing degree of PAE substitution. Vitamin B2 (VB2), as a model nutrient, was encapsulated into the nanoparticles. The drug-loading content increased with increasing degree of PAE substitution. The maximum VB2 loading capacity and loading efficiency of PEA3 nanoparticles were 3.53 ± 0.03% and 91.48 ± 0.80%, respectively. The in vitro release behavior of VB2 from the PEA-NPs showed a biphasic release profile with an initial burst release of about 40–50% of VB2 in the first 10 h followed by a steady and continuous release phase for the following 50 h in PBS, pH 7.4. The human colorectal carcinoma cell line was used to investigate the cytotoxicity of PEA-NPs. Our results showed that various concentrations of nanoparticles did not cause significant cytotoxicity against cell lines at normal concentrations.
Antibacterial surfaces have been in the focus of research for years, driven by an unmet clinical need to manage an increasing incidence of implant-associated infections. The use of silver has become a topic of interest because of its proven broad-spectrum antibacterial activity and track record as a coating agent of soft tissue implants and catheters. However, for the time being, the translation of these technological achievements for the improvement of the antibacterial property of hard tissue titanium (Ti) implants remains unsolved. In our study, we focused on the investigation of the photocatalysis mediated antibacterial activity of silver (Ag), and Ti nanoparticles instead of their pharmacological effects. We found that the photosensitisation of commercially pure titanium discs by coating them with an acrylate-based copolymer that embeds coupled Ag/Ti nanoparticles can initiate the photocatalytic decomposition of adsorbed S. salivarius after the irradiation with an ordinary visible light source. The clinical isolate of S. salivarius was characterised with MALDI-TOF mass spectrometer, while the multiplication of the bacteria on the surface of the discs was followed-up by MTT assay. Concerning practical relevance, the infected implant surfaces can be made accessible and irradiated by dental curing units with LED and plasma arc light sources, our research suggests that photocatalytic copolymer coating films may offer a promising solution for the improvement of the antibacterial properties of dental implants.
Glucocorticoids are powerful anti-inflammatory, immunosuppressive, and anti-proliferative agents. The aim of this study was to evaluate the effectiveness of a prednisolone- (PDScs) and sirolimus-coated stent (SRLcs) in preventing artery vessel neointimal hyperplasia and inflammatory reactions in vitro and in vivo. PDS, a synthetic glucocorticoid, is a derivative of cortisol, which is used to treat a variety of inflammatory and autoimmune conditions. The stents were fabricated with PDS, SRL, or both agents using a layer-by-layer coating system (designated as PDScs, SRLcs, and PDSRLcs, respectively). The surface morphology of the PDScs showed an evenly dispersed and roughened shape, which was smoothened by the SRL coating. Half of the total drug amounts were released within seven days, followed by an additional release, which continued for up to 28 days. The proliferation of smooth muscle cells was inhibited in the SRLcs group (31.5 ± 4.08%), and this effect was enhanced by PDS addition (PDSRLcs, 46.8 ± 8.11%). Consistently, in the animal study, the restenosis rate was inhibited by the SRLcs and PDSRLcs (18.5 ± 6.23% and 14.5 ± 3.55%, respectively). Especially, fibrin expression and inflammation were suppressed in the PDS-containing group (PDScs, 0.6 ± 0.12 and 1.4 ± 0.33; PDSRLcs, 0.7 ± 0.48 and 1.7 ± 0.12, respectively) compared to PDS non-containing groups (BMS, 1.1 ± 0.12, and 1.8 ± 0.55; SRLcs, 1.6 ± 0.32 and 2.0 ± 0.62, respectively). Moreover, re-endothelialization was enhanced in the PDScs group as determined using immunohistochemistry with a cluster of differentiation (CD)-31 antibodies. These results suggest that the inhibitory effect of SRLcs on anti-restenosis can be accelerated by additional coating with PDS, which has promising properties as a bioactive compound with useful anti-inflammatory effects.
Drug-releasing implants are gaining increasing interest. The present study reports a detailed physicochemical analysis of a polymeric coating based on poly(D,L-lactide) and the incorporated gentamicin combined with an in vitro and in vivo study of the gentamicin release. Differential scanning calorimeter, Fourier transform infrared spectroscopy, gel permeation chromatography and high-performance liquid chromatography showed no effect of the gamma sterilisation on the coating components or an interaction of the polymer and the gentamicin. Microbiological analysis revealed an inhibition of bacterial growth on the implant surface. For the in vivo study, gentamicin-coated wires were implanted into the tibiae of rats and harvested at different time points up to day 42. To monitor the release in vivo, gentamicin was quantified in serum, bone, endosteum, kidney, and on the explanted wires. Gentamicin was detectable over a time period of 42 days in the endosteum, up to seven days in the kidney, up to 4 h in the bone and at the end of the experiment on one of eight wires. The locally released gentamicin caused no histological changes of the kidney. Microbiologically active concentrations of released gentamicin were found in the endosteum up to 4 h after implantation. The combination of different methods supports the individual results, where quantification is complemented by visualisation or antimicrobial activity. This work demonstrates that the coating procedure results in no substantial alteration of the incorporated drug and that the in vitro burst release occurs also in vivo.
Heart valve-related disorders are among the major causes of death worldwide. Although prosthetic valves are widely used to treat this pathology, current prosthetic grafts cannot grow with the patient while maintaining normal valve mechanical and hemodynamic properties. Tissue engineering may provide a possible solution to this issue through using biodegradable scaffolds and patients’ own cells. Despite their similarity to heart valve tissue, most hydrogel scaffolds are not mechanically suitable for the dynamic stresses of the heart valve microenvironment. In this study, we integrated electrospun poly(glycerol sebacate) (PGS)–poly(-caprolactone) (PCL) microfiber scaffolds, which possess enhanced mechanical properties for heart valve engineering, within a hybrid hydrogel made from methacrylated hyaluronic acid and methacrylated gelatin. Sheep mitral valvular interstitial cells were encapsulated in the hydrogel and evaluated in hydrogel-only, PGS–PCL scaffold-only, and composite scaffold conditions. Although the cellular viability and metabolic activity were similar among all scaffold types, the presence of the hydrogel improved the three-dimensional distribution of mitral valvular interstitial cells. As seen by similar values in both the Young’s modulus and the ultimate tensile strength between the PGS–PCL scaffolds and the composites, microfibrous scaffolds preserved their mechanical properties in the presence of the hydrogels. Compared to electrospun or hydrogel scaffolds alone, this combined system may provide a more suitable three-dimensional structure for generating scaffolds for heart valve tissue engineering.
Anti-tumor necrosis factor α (TNFα) drugs such as etanercept (ETN) have been mostly used in systemic treatment of rheumatoid arthritis. To eliminate the side effects in long-term treatments and to achieve a local sustained anti-inflammatory effect, a controlled drug delivery system is needed for anti-TNFα drugs. This study aims to develop novel injectable microcarriers of ETN that can provide long-term controlled release of this protein drug upon intra-articular application. In this study, poly(-caprolactone) (PCL) and its copolymer with poly(ethylene glycol), methoxypoly(ethylene glycol)-poly(-caprolactone)-methoxypoly(ethylene glycol) microspheres (MPEG-PCL-MPEG) were compared for their prospective success in rheumatoid arthritis treatment. Microspheres with smooth surface of a mean particle diameter of approximately 5 μm were prepared with both polymers. MPEG-PCL-MPEG microspheres had higher encapsulation efficiency than PCL microspheres. The activity of encapsulated ETN within MPEG-PCL-MPEG microspheres also retained while 90% of the activity of ETN within PCL microspheres could retain during 90-day release. MPEG-PCL-MPEG microspheres showed faster ETN release compared to PCL microspheres in various release media. Cumulative amounts of ETN released from both types of microspheres were significantly lower in cell culture medium and in synovial fluids than in phosphate buffered saline. This was mainly due to protein adsorption onto microspheres. Hydrophilic MPEG segment enhanced ETN release while preventing protein adsorption on microspheres compared to PCL. Sustained ETN release from microspheres resulted with a significant decrease in pro-inflammatory cytokines (TNFα, IFN, IL-6, IL-17) and MMP levels (MMP-3, MMP-13), while conserving viability of fibroblast-like synoviocytes compared to the free drug. Results suggest that MPEG-PCL-MPEG is a potential copolymer of PCL that can be used in development of biomedical materials for effective local treatment purposes in chronic inflammatory arthritis owing to enhanced hydrophilicity. Yet, PCL microspheres are also promising systems having good compatibility to synoviocytes and would be especially the choice for treatment approach requiring longer term and slower release.
Silica-based sol–gel coatings have gained attention in bone therapies and orthopedic applications, due to the biocompatibility and bioactivity, including a high potential for the controlled release both in vitro and in vivo. Bioactive materials are created to facilitate the biocompatibility of orthopedic implants. One of the promising alternatives is biomaterials with immobilized drugs. In this study we demonstrated for the first time novel sol–gel-derived silica coatings with active amino groups (SiO2(NH2)) functionalized with a steroid drug—betamethasone, applied to a substrate 316 L using dip coating technique. The presence of betamethasone in functionalized coatings was directly confirmed by Raman spectroscopy and energy-dispersive X-ray spectroscopic analysis. The wettability was evaluated by the sessile drop method, while the surface free energy was estimated based on the contact angles measured. Our results showed a shift in surface properties from hydrophobic to hydrophilic after application of the coatings. We have investigated the morphology, proliferation factor, and the population doubling time of adipose-derived stem cells for biological purposes. Moreover, the analysis of the distribution and localization of cellular microvesicles was performed to evaluate the influence of functionalized surfaces on cellular cytophysiological activity. Increased proliferation and activation of cells, determined by the observations of microvesicles shedding processes, provided evidence of the availability of the drug. Therefore, we conclude that the sol–gel synthesis proposed here allows to improve the metal substrates and can be successfully used for immobilization of betamethasone. This in turn enables the direct delivery of the drug with implanted material into the wound site, and to stimulate the activity of cells to enhance tissue regeneration.
We demonstrate that coating calcium sulfate with deacetylated chitosan enhances the elution profile of daptomycin by prolonging the period during which high concentrations of antibiotic are released. Coatings reduced initial bolus release of daptomycin by a factor of 10 to approximately 1000 µg/ml, and levels remained above 100 µg/ml for up to 10 days. Chitosan-coated and uncoated calcium sulfate implants with and without 15% daptomycin were evaluated in an experimental model of staphylococcal osteomyelitis through bacteriology scores, radiology, histopathology, and Gram staining. Significant reduction in bacteriology scores was observed for implants containing daptomycin and coated with chitosan compared with all the other groups. We confirm that the use of chitosan-coated calcium sulfate beads for local antibiotic delivery can be correlated with an improved therapeutic outcome following surgical debridement in the treatment of chronic osteomyelitis.
Hyperthermia has been suggested as a novel, minimally invasive cancer treatment method. After implantation of magnetic nano- or microparticles around a tumour through blood vessels, irradiation with alternating magnetic fields facilitates the efficient in situ hyperthermia even for deep-seated tumours. On the basis of this idea, if the microspheres are capable of delivering drugs, they could be promising multifunctional biomaterials effective for chemotherapy as well as hyperthermia. In the present study, magnetite microspheres were prepared by aggregation of the iron oxide colloid in water-in-oil (W/O) emulsion. The release behaviour of alendronate, a typical bisphosphonate, from the microspheres was examined in vitro as a model of the bone tumour prevention and treatment system. The alendronate was successfully incorporated onto the porous magnetite microspheres in vacuum conditions. The drug-loaded microspheres maintained their original spherical shapes even after shaking in ultrapure water for 3 days, suggesting that they have sufficient mechanical integrity for clinical use. It was attributed to high aggregation capability of the magnetite nanoparticles through van der Waals and weak magnetic attractions. The microspheres showed slow release of the alendronate in vitro, resulting from tight covalent or ionic interaction between the magnetite and the alendronate. The release rate was diffusion-controlled type and well controlled by the alendronate concentration in drug incorporation to the microspheres.
An experimental and computational investigation of the self-tapping ability of carbon fibre reinforced polyetheretherketone (CFR-PEEK) has been conducted. Six CFR-PEEK suture anchor designs were investigated using PEEK-OPTIMA® Reinforced, a medical grade of CFR-PEEK. Experimental tests were conducted to investigate the maximum axial force and torque required for self-taping insertion of each anchor design. Additional experimental tests were conducted for some anchor designs using pilot holes. Computational simulations were conducted to determine the maximum stress in each anchor design at various stages of insertion. Simulations also were performed to investigate the effect of wall thickness in the anchor head. The maximum axial force required to insert a self-tapping CFR-PEEK suture anchor did not exceed 150 N for any anchor design. The maximum torque required to insert a self-tapping CFR-PEEK suture anchor did not exceed 0.8 Nm. Computational simulations reveal significant stress concentrations in the region of the anchor tip, demonstrating that a re-design of the tip geometry should be performed to avoid fracture during self-tapping, as observed in the experimental component of this study. This study demonstrates the ability of PEEK-OPTIMA Reinforced suture anchors to self-tap polyurethane foam bone analogue. This provides motivation to further investigate the self-tapping ability of CFR-PEEK suture anchors in animal/cadaveric bone. An optimised design for CFR-PEEK suture anchors offers the advantages of radiolucency, and mechanical properties similar to bone with the ability to self-tap. This may have positive implications for reducing surgery times and the associated costs with the procedure.
Biocompatible and temperature-sensitive amphiphilic polymeric micelles comprised of poly(succinimide)-g-poly(N-isopropylacrylamide-co-N,N-dimethylacrylamide) (PSI-g-poly(NIPAAm-co-DMAAm)) were synthesized to use as new drug carriers. The PSI-co-poly(PNIPAAm-co-DMAAm) polymers were prepared by nucleophilic opening of poly(succinimide) using amino-terminated poly(NIPAAm-co-DMAAm). The lower critical solution temperature of the copolymer was 40.6℃ higher than normal human body temperature. The blank polymeric micelles were observed to have a regular spherical shape, and the particle sizes were approximately 85 nm. This copolymer exhibited no significant cytotoxicity and hemolysis indicated that the micelles had good biocompatibility. In addition, these polymeric micelles encapsulated the anti-inflammatory drug, hesperetin, in the inner core with a drug loading content of approximately 20%. The release profiles of hesperetin showed a significant temperature-sensitive switching behavior. The hesperetin release response was dramatically lower at a temperature below the lower critical solution temperature as compared with a temperature above the lower critical solution temperature. The lipopolysaccharide-induced nitric oxide production inhibition experiments demonstrated that hesperetin-encapsulated micelles showed a significant reduction. In this study, the biocompatible temperature-sensitive micelles based on PSI-g-poly(NIPAAm-co-DMAAm) have great potential to act as a suitable carrier for drug delivery.
Bio-based high elastic polyurethanes were prepared from hexamethylene diisocyanate and various ratios of isosorbide to poly(tetramethylene glycol) as a diol by a simple one-shot bulk polymerization without a catalyst. Successful synthesis of the polyurethanes was confirmed by Fourier transform-infrared spectroscopy and 1H nuclear magnetic resonance. Thermal properties were determined by differential scanning calorimetry and thermogravimetric analysis. The glass transition temperature was –47.8℃. The test results showed that the poly(tetramethylene glycol)/isosorbide-based elastomer exhibited not only excellent stress–strain properties but also superior resilience to the existing polyether-based polyurethane elastomers. The static and dynamic properties of the polyether/isosorbide-based thermoplastic elastomer were more suitable for dynamic applications. Moreover, such rigid diols impart biocompatible and bioactive properties to thermoplastic polyurethane elastomers. Degradation tests performed at 37℃ in phosphate buffer solution showed a mass loss of 4–9% after 8 weeks, except for the polyurethane with the lowest isosorbide content, which showed an initial rapid weight loss. These polyurethanes offer significant promise due to soft, flexible and biocompatible properties for soft tissue augmentation and regeneration.
The local microenvironment plays an important role in maintaining the dynamics of the extracellular matrix and the cell–extracellular matrix relationship. The extracellular matrix is a complex network of macromolecules with distinct mechanical and biochemical characteristics. Disruptions in extracellular matrix homeostasis are associated with the onset of cancer. The extracellular matrix becomes highly disorganized, and the cell–matrix relationship changes, resulting in altered cell-signaling processes and metastasis. Medulloblastoma is one of the most common malignant pediatric brain tumors in the United States. In order to gain a better understanding of the interplay between cell–extracellular matrix interactions and cell-migratory responses in tumors, eight different matrix macromolecule formulations were investigated using a medulloblastoma-derived cell line: poly-
Collagen- and gelatin-coated porous spherical granule was prepared by slurry dripping process using biphasic calcium phosphate powder. The coating was stabilized by cross-linking with dimethyl 3,3'-dithiobispropionimidate di-hydrogenchloride (DTBP). Afer DTBP cross-linking, the nanostructure of collagen- and gelatin-coated surfaces was changed from smooth to fibrous and net-like structure. Excellent cross-linking of the coating was seen as indicated by the differential scanning calorimetry thermogram and the Fourier transform infrared spectroscopy spectra. After cross-linking the relative intensities of the Fourier transform infrared spectroscopy peaks were decreased and amide bands were shifted to the left. The interaction of gelatin with DTBP cross-linking agent was stronger than that with collagen according to differential scanning calorimetry and Fourier transform infrared spectroscopy results. The compressive strength of the granular bone substitutes increased significantly after the coating process and gelatin coated biphasic calcium phosphate granules showed highest value at 3.68 MPa after cross-linking. Porosity was greater than 63% and did not change significantly with coating. Biocompatibility investigation by in vitro and in vivo showed that the coating improved the cell proliferation marginally. However, the cross-linking process did not jeopardize the excellent biocompatibility of collagen and gelatin. The in vivo study confirms better bone formation behavior of the cross-linked gelatin and collagen coated samples investigated for 8 weeks in vivo.
Nanocellulose from wood is a promising material with potential in various technological areas. Within biomedical applications, nanocellulose has been proposed as a suitable nano-material for wound dressings. This is based on the capability of the material to self-assemble into 3D micro-porous structures, which among others have an excellent capacity of maintaining a moist environment. In addition, the surface chemistry of nanocellulose is suitable for various applications. First, OH-groups are abundant in nanocellulose materials, making the material strongly hydrophilic. Second, the surface chemistry can be modified, introducing aldehyde and carboxyl groups, which have major potential for surface functionalization. In this study, we demonstrate the production of nanocellulose with tailor-made surface chemistry, by pre-treating the raw cellulose fibres with carboxymethylation and periodate oxidation. The pre-treatments yielded a highly nanofibrillated material, with significant amounts of aldehyde and carboxyl groups. Importantly, the poly-anionic surface of the oxidized nanocellulose opens up for novel applications, i.e. micro-porous materials with pH-responsive characteristics. This is due to the swelling capacity of the 3D micro-porous structures, which have ionisable functional groups. In this study, we demonstrated that nanocellulose gels have a significantly higher swelling degree in neutral and alkaline conditions, compared to an acid environment (pH 3). Such a capability can potentially be applied in chronic wounds for controlled and intelligent release of antibacterial components into biofilms.
Electrospun fibers with an average fiber diameter in the nanometer range were prepared from soy protein isolate to develop scaffolds for tissue engineering applications. Poly(ethylene oxide) was added to facilitate fiber formation. The influence of processing parameters such as applied voltage, soy protein isolate and poly(ethylene oxide) concentrations, and poly(ethylene oxide) molecular weight on electrospun fiber morphology was investigated. Resulting soy protein isolate/poly(ethylene oxide) mats were carbodiimide crosslinked to increase construct robustness. Mechanical properties and in vitro biocompatibility of crosslinked electrospun scaffolds were evaluated. Soy protein isolate/poly(ethylene oxide) fiber diameters ranged between 50 and 270 nm depending on both electrospinning and solution parameters. The Young’s modulus for 7% soy protein isolate/3% poly(ethylene oxide) and 12% soy protein isolate/3% poly(ethylene oxide) electrospun scaffolds were 75 and 252 kPa, respectively. Human mesenchymal stem cell studies showed successful cell adhesion and proliferation on the soy protein isolate/poly(ethylene oxide) fibers. The structural and biological properties of these soy protein isolate electrospun scaffolds suggest their potential applications in tissue engineering.
Glioma is the most common brain malignancy with poor prognosis. The current treatments for gliomas are mainly based on surgery, chemotherapy, and radiotherapy, which exhibit limited efficacy. Photodynamic therapy (PDT) using photosensitizers has been applied to glioma therapy. However, different photosensitizers usually lead to different therapeutic effects and adverse reactions.
This study investigates the anti-tumor effect of photosensitizer ZnPcS4-BSA in xenograft glioma tumors.
The xenograft glioma tumor model was established by inoculating nude mice with U251 cells. Tumor growth was evaluated by tumor volume, weight, and inhibition rate. Cell apoptosis was evaluated using TUNEL staining. Vascular endothelial growth factor (VEGF) expression and microvessel density were measured by immunohistochemistry.
Significant decreases in tumor volume and weight as well as significant increases in tumor inhibition rate, cell apoptosis, VEGF expression, and microvessel density were observed in mice in the low- and high-dose PDT groups compared to the control, irradiation alone, and photosensitizer alone groups. No significant difference in cytotoxicity was observed between control group and photosensitizer alone group. Photosensitizer ZnPcS4-BSA significantly inhibited xenograft glioma tumor growth through induction of apoptosis.
PDT using ZnPcS4-BSA may be effective for the therapy of gliomas.
Fabricating scaffolds that can simulate the architecture and functionality of native extracellular matrix is a huge challenge in vascular tissue engineering. Various kinds of materials are engineered via nano-technological approaches to meet the current challenges in vascular tissue regeneration. During this study, nanofibers from pure polyurethane and hybrid polyurethane/collagen in two different morphologies (random and aligned) and in three different ratios of polyurethane:collagen (75:25; 50:50; 25:75) are fabricated by electrospinning. The fiber diameters of the nanofibrous scaffolds are in the range of 174–453 nm and 145–419 for random and aligned fibers, respectively, where they closely mimic the nanoscale dimensions of native extracellular matrix. The aligned polyurethane/collagen nanofibers expressed anisotropic wettability with mechanical properties which is suitable for regeneration of the artery. After 12 days of human aortic smooth muscle cells culture on different scaffolds, the proliferation of smooth muscle cells on hybrid polyurethane/collagen (3:1) nanofibers was 173% and 212% higher than on pure polyurethane scaffolds for random and aligned scaffolds, respectively. The results of cell morphology and protein staining showed that the aligned polyurethane/collagen (3:1) scaffold promote smooth muscle cells alignment through contact guidance, while the random polyurethane/collagen (3:1) also guided cell orientation most probably due to the inherent biochemical composition. Our studies demonstrate the potential of aligned and random polyurethane/collagen (3:1) as promising substrates for vascular tissue regeneration.
Microporous, poly (-caprolactone) (PCL) matrices loaded with the antibacterial, metronidazole were produced by rapidly cooling suspensions of drug powder in PCL solutions in acetone. Drug incorporation in the matrices increased from 2.0% to 10.6% w/w on raising the drug loading of the PCL solution from 5% to 20% w/w measured with respect to the PCL content. Drug loading efficiencies of 40–53% were obtained. Rapid ‘burst release’ of 35–55% of the metronidazole content was recorded over 24 h when matrices were immersed in simulated vaginal fluid (SVF), due to the presence of large amounts of drug on matrix surface as revealed by Raman microscopy. Gradual release of around 80% of the drug content occurred over the following 12 days. Metronidazole released from PCL matrices in SVF retained antimicrobial activity against Gardnerella vaginalis in vitro at levels up to 97% compared to the free drug. Basic modelling predicted that the concentrations of metronidazole released into vaginal fluid in vivo from a PCL matrix in the form of an intravaginal ring would exceed the minimum inhibitory concentration of metronidazole against G. vaginalis. These findings recommend further investigation of PCL matrices as intravaginal devices for controlled delivery of metronidazole in the treatment and prevention of bacterial vaginosis.
The poor retention and efficacy of instilled drops as a means of delivering drugs to the ophthalmic environment is well-recognised. The potential value of contact lenses as a means of ophthalmic drug delivery, and consequent improvement of pre-corneal retention is one obvious route to the development of a more effective ocular delivery system. Furthermore, the increasing availability and clinical use of daily disposable contact lenses provides the platform for the development of viable single-day use drug delivery devices based on existing materials and lenses. In order to provide a basis for the effective design of such devices, a systematic understanding of the factors affecting the interaction of individual drugs with the lens matrix is required. Because a large number of potential structural variables are involved, it is necessary to achieve some rationalisation of the parameters and physicochemical properties (such as molecular weight, charge, partition coefficients) that influence drug interactions. Ophthalmic dyes and structurally related compounds based on the same core structure were used to investigate these various factors and the way in which they can be used in concert to design effective release systems for structurally different drugs. Initial studies of passive diffusional release form a necessary precursor to the investigation of the features of the ocular environment that over-ride this simple behaviour. Commercially available contact lenses of differing structural classifications were used to study factors affecting the uptake of the surrogate actives and their release under ‘passive’ conditions. The interaction between active and lens material shows considerable and complex structure dependence, which is not simply related to equilibrium water content. The structure of the polymer matrix itself was found to have the dominant controlling influence on active uptake; hydrophobic interaction with the ophthalmic dye playing a major role.
The purpose of this research was to develop novel nanoparticles (NPs) of star-like copolymer mannitol-functionalized poly(lactide)-vitamin E TPGS (M-PLA-TPGS) for paclitaxel delivery for prostate cancer treatment, and evaluate their therapeutic effects in prostate cancer cell line and animal model in comparison with the linear PLGA NPs and poly(lactide)-vitamin E TPGS (PLA-TPGS) NPs. The paclitaxel-loaded M-PLA-TPGS NPs, prepared by a modified nano-precipitation method, were observed by FESEM to be near-spherical shape with narrow size distribution. The drug-loaded NPs were further characterized in terms of size, surface charge, drug content, encapsulation efficiency and in vitro drug release. The results showed that the M-PLA-TPGS NPs were found to be stable, showing almost no change in particle size and surface charge during the three-month storage period. In vitro drug release exhibited biphasic pattern with initial burst release followed by slow and continuous release. The cellular uptake level of M-PLA-TPGS NPs was demonstrated higher than linear PLGA NPs and PLA-TPGS NPs in PC-3 cells. The data also showed that the paclitaxel-loaded M-PLA-TPGS nanoparticles have higher antitumor efficacy than that of linear PLA-TPGS nanoparticles and PLGA nanoparticles in vitro and in vivo. In summary, the star-like copolymer M-PLA-TPGS could be used as a potential and promising molecular biomaterial in developing novel nanoformulation for prostate cancer treatment.
In this study, a phosphorylation treatment of porous anodic alumina (PAA) was performed by wet impregnation in phosphoric acid and a subsequent heat treatment. The PAA and phosphorylated PAA specimens were analyzed using a field emission scanning electron microscope, an energy-dispersive X-ray spectrometer, and Fourier transform infrared spectroscopy. The apatite-forming ability of the phosphorylated PAA was evaluated by soaking the specimens in simulated body fluid for 1, 3, and 7 days. The surface microstructures and chemical property changes after soaking in simulated body fluid were again characterized by field emission scanning electron microscope, energy-dispersive X-ray spectrometer, and Fourier transform infrared spectroscopy. Results of this study demonstrated that the functional –PO4 groups introduced onto the PAA surface dramatically promoted the deposition of bone-like apatite on PAA. The results from this study indicated that the phosphorylation treatment of anodic alumina is an effective method for inducing bone-like apatite formation, and this phosphorylated PAA can be a promising candidate to be used as bioactive surface coatings on implant metals and alloys for orthopedic and dental applications.
The relationship between the delivery of dexamethasone and the composition of silicone hydrogel materials was investigated. Two hydrophilic monomers (2-hydroxyethyl methacrylate or N,N-dimethylacrylamide), a siloxy methacrylate-based monomer (1-(Bis(trimethylsiloxy)methylsilyl)propoxy-3-metacryloxy-2-propanol, a polysiloxane (monomethacryloxypropyl-terminated polydimethylsiloxane) and a polymerizable silicone surfactant (Silmer ACR A008-UP) were used to synthesize silicone hydrogels of variable composition. The materials properties, such as surface wettability and equilibrium water content, were highly dependent on polymer composition. All dexamethasone-loaded hydrogels showed uptake that was driven primarily by sorption to the polymer phase. Furthermore, a positive correlation between loading mass and equilibrium water content was established. The duration of drug release from the hydrogels ranged from one to greater than two weeks depending on the monomer composition and relative contribution of hydrophilic and hydrophobic monomers. Higuchi model rate constants for the release showed strong correlation with the equilibrium water content, signifying that the release is likely controlled by aqueous phase diffusion.
To facilitate the healing of chronic wounds, growth factors such as epidermal growth factor need to be safely encapsulated for their sustained and effective delivery to the wound bed. Using a layer-by-layer assembly technique, epidermal growth factor is successfully encapsulated on the surface of poly(acrylic acid)-modified polyurethane film. The amount of encapsulated epidermal growth factor is controlled by adjusting the number of chitosan/epidermal growth factor bilayers. A controlled release of epidermal growth factor from the surface of polyurethane film for a period of five days is achieved with well-retained bioactivity (over 90%) as evidenced by a cell proliferation assay. In an in vitro cellular wounding assay, the cell gap covered with the epidermal growth factor-loaded polyurethane film closes at a rate more than twice as fast as that covered with a control polyurethane film. Fluorescent staining of F-actin reveals that the released epidermal growth factor induces differences in cytoskeletal organization, suggesting that stimulated cell migration also contributes to the close of the cell gap.
Degradable magnesium alloys are promising biomaterials for orthopedic applications. The aim of this study was to evaluate the potential effects on both the synovial membrane (synovialis) and the synovial fluid (synovia) of the degradation products of a MgYREZr-pin implanted in the intercondylar femoral notch in a rabbit model. Thirty-six animals were randomized into two groups (MgYREZr or Ti6Al4V alloy) of 18 animals each. Each group was then divided into three subgroups with implantation periods of 1, 4, and 12 weeks, with six animals in each subgroup. The initial inflammatory reaction caused by the surgical trauma declined after 12 weeks of implantation, and elucidated a progressive recovery of the synovial membrane. Compared with control Ti6Al4V pins, there were no significant differences between the groups. However, after 12 weeks, recovery of the synovial membrane was more advanced in the titanium group, in which 92% showed no signs of synovitis, than in the magnesium group. A cytotoxicity test with L929 cells and human osteoblasts (HOB) was also conducted, according to EN ISO 10993-5/12, and no toxic leachable products were observed after 24 h of incubation. In conclusion, the MgYREZr alloy seems to be a suitable material for intra-articular degradable implants.
Cyclophosphamide (CP) is the most commonly used chemotherapeutic drug for various types of cancer. However, its use causes severe cytotoxicity to normal cells in human. It is well known that the undesirable side effects are caused due to the formation of reactive oxygen species. Selenium is an essential micronutrient for both animals and humans and has antioxidant and membrane stabilizing property, but selenium is also toxic above certain level. Nano selenium has been well proved to be less toxic than inorganic selenium as well as certain organoselenium compounds. The objective of the study is to evaluate the protective role of Nano-Se against CP-induced hepatotoxicity and genotoxicity in Swiss albino mice. CP was administered intraperitoneally (25 mg/kg b.w.) and Nano-Se was given by oral gavages (2 mg Se/kg b.w.) in concomitant and pretreatment scheme. Intraperitoneal administration of CP induced hepatic damage as indicated by the serum marker enzymes aspartate and alanine transaminases and increased the malonaldehyde level, depleted the glutathione content and antioxidant enzyme activity (glutathione peroxidase, glutathione-s-transferase, superoxide dismutase and catalase), and induced DNA damage and chromosomal aberration. Oral administration of Nano-Se caused a significant reduction in malonaldehyde, ROS level and glutathione levels, restoration of antioxidant enzyme activity, reduction in chromosomal aberration in bone marrow, and DNA damage in lymphocytes and also in bone marrow. Moreover, the chemoprotective efficiency of Nano-Se against CP induced toxicity was confirmed by histopathological evaluation. The results support the protective effect of Nano-Se against CP-induced hepatotoxicity and genotoxicity.
Calcium phosphate crystals, as the main component of dentin and enamel, have been widely used for the occlusion of dentinal tubules. However, the low bond strength and poor sealing effect limit their clinical practicality. In this study, a collagen/calcium dual-affinitive peptide E8DS (EEEEEEEEDSpESpSpEEDR) and nano-hydroxyapatite (nano-HAp) flocculi were developed to seal dentin tubules for reducing dentin hypersensitivity, whereas the E8DS peptides were pre-applied to improve the adhesion of occlusive hydroxyapatite coating on dentin collagen matrix for the long-lasting sealing effect and relief from hypersensitivity. Our study showed that E8DS peptides had a strong affinity with dentin collageneous matrix that almost 43.7% of initial E8DS peptides immobilized on exposed dentin samples remained detained after continuous washing by distilled water for four weeks at a rate of 1 mL/min. Nano-HAp flocculi were obtained by re-neutralization of HAp-HCl solution and then brushed onto the surfaces of pre-treated human dentin disks with E8DS peptides, which showed a perfect occlusion of exposed dentinal tubules, as compared with Nano-HAp only and a commercial desensitizer, Green Or. With only around 10-min E8DS peptide pre-treatment, the occlusive mineral layers remained intact against consecutively stirred washing in phosphate-buffered saline or coke for 15 min, and 6 min of tooth-brushing, which implied that our E8DS peptide could comparatively improve the durability of sealant-dentin interface bonds for long-lasting dentine desensitization.
Hyperthermia is a technique for destroying cancer cells which involves the exposition of body's tissue to a controlled heat, normally between 41°C and 46°C. It has been reported that ferro- or ferrimagnetic materials can heat locally, if they are placed (after being implanted) under an alternating magnetic field, damaging only tumoral cells and not the healthy ones. The power loss produced by the magnetic materials can be dissipated in the form of heat. This phenomenon has to be regulated in order to obtain a controlled temperature inside the tissues.
The material that was produced and characterized in this work is composed of two phases: a polymethylmethacrylate (PMMA) matrix in which a ferrimagnetic biocompatible/bioactive glass ceramic is dispersed. This composite material is intended to be applied as bone filler for the hyperthermic treatment of bone tumors. The ferrimagnetic bioactive glass-ceramic belongs to the system SiO2–Na2O–CaO–P2O5–FeO–Fe2O3 and contains magnetite (FeO*Fe2O3) inside an amorphous bioactive residual phase. The composite material possesses structural, magnetic and bioactivity properties. The structural ones are conferred by PMMA which acts as filler for the bone defect or its damaged area. Bioactivity is conferred by the composition of the residual amorphous phase of the glass-ceramic and magnetic properties are conferred by magnetite crystals embedded in the bioactive glass-ceramic.
The characterization involved the following tests: morphological and chemical characterization (scanning electron microscopy–energy dispersion spectrometry–micro computed tomography analysis), calorimetric tests and mechanical test (compression and flexural four point test).
In vitro assessment of biological behavior will be the object of the part II of this work.
Carbon-fibre-reinforced polyether ether ketone (CFR-PEEK) exhibits excellent biomechanical properties as it has an elastic modulus similar to bone. However, CFR-PEEK displays inferior biocompatibility compared with titanium alloy and coating techniques are therefore of interest in order to improve integration. In this paper, the early biological response to CFR-PEEK implants, with and without hydroxyapatite coating, was investigated. Furthermore, a hydroxyapatite-coated titanium alloy reference served as a clinically relevant control. The study was conducted in a rabbit model, both in femur trabecular bone as well as in tibia cortical bone. The results demonstrated that an hydroxyapatite coating significantly enhances the bone response to PEEK implants in vivo. Moreover, in cortical bone, hydroxyapatite-coated PEEK implants induced superior bone response compared with hydroxyapatite-coated Ti ones. These results suggest that hydroxyapatite-coated CFR-PEEK is a suitable material for in vivo implantation.
The aim of this study was to compare the osteogenic effects of periodontal ligament stem cells (PDLSCs) versus bone marrow mesenchymal stem cells (BMMSCs) in combination with Bio-Oss scaffolds on subcutaneous and critical-size defects in the immunodeficient rat calvarium. PDLSCs and BMMSCs were obtained from the same canine donor. Twenty-four rats were randomly assigned to one of four experimental groups (n = 6 each): group A (no-graft negative control), group B (Bio-Oss positive control), group C (BMMSC/Bio-Oss test group), and group D (PDLSC/Bio-Oss test group). Eight weeks post-transplantation, ectopic and in situ bone regeneration was evaluated by micro-computed tomography (µ-CT), histology, histomorphometry, and immunohistochemistry. The stem cell/Bio-Oss constructs were significantly superior to the controls in terms of their ability to promote osteogenesis (p < 0.01), while the PDLSC/Bio-Oss construct tended to be superior to the BMMSC/Bio-Oss construct. Thus, engineered stem cell/Bio-Oss complexes can successfully reconstruct critical-size defects in rats, and PDLSCs and BMMSCs are both suitable as seed cells.
The incorporation of carboxyl functionalised multi-walled carbon nanotube (MWCNT-COOH) into a leading proprietary grade orthopaedic bone cement (Simplex P™) at 0.1 wt% has been investigated. Resultant static and fatigue mechanical properties, in addition to thermal and polymerisation properties, have been determined. Significant improvements (p ≤ 0.001) in bending strength (42%), bending modulus (55%) and fracture toughness (22%) were demonstrated. Fatigue properties were improved (p ≤ 0.001), with mean number of cycles to failure and fatigue performance index being increased by 64% and 52%, respectively. Thermal necrosis index values at ≥44°C and ≥55°C were significantly reduced (p ≤ 0.001) (28% and 27%) versus the control. Furthermore, the onset of polymerisation increased by 58% (p < 0.001), as did the duration of the polymerisation reaction (52%). Peak energy during polymerisation increased by 672% (p < 0.001). Peak area of polymerisation increased by 116% (p < 0.001) indicating that the incorporation of MWCNT-COOH reduced the rate of polymerisation significantly. A non-significant reduction (8%) in percentage monomer conversion was also recorded. Raman spectroscopy clearly showed that the addition of MWCNT-COOH increased the ratio between normalised intensities of the G-Band and D-Band (IG/ID ), and also increased the theoretical compressive strain (–1.72%) exerted on the MWCNT-COOH by the Simplex P™ cement matrix. Therefore, demonstrating a level of chemical interactivity between the MWCNT-COOH and the Simplex P™ bone cement exists and consequently a more effective mechanism for successful transfer of mechanical load. The extent of homogenous dispersion of the MWCNT-COOH throughout the bone cement was determined using Raman mapping.
Recently, silk fibroin scaffolds have been introduced as novel and promising biomaterials in the field of cardiac tissue engineering. This study was designed to compare infiltration, proliferation, and cardiac differentiation potential of menstrual blood-derived stem cells (MenSCs) versus bone marrow-derived mesenchymal stem cells (BMSCs) in Bombyx mori-derived silk scaffold. Our primary data revealed that the fabricated scaffold has mechanical and physical qualities suitable for cardiac tissue engineering. The MenSCs tracking in scaffolds using immunofluorescent staining and scanning electron microscopy confirmed MenSCs attachment, penetration, and distribution within the porous scaffold matrix. Based on proliferation assay using propidium iodide DNA quantification, the significantly higher level of growth rates of both MenSCs and BMSCs was documented in scaffolds than that in two-dimensional culture (p < 0.01). The expression level of TNNT2, a bona fide cardiac differentiation marker, in BMSCs differentiated on silk scaffolds was markedly higher than those cultured in two-dimensional culture indicating the improvement of cardiac differentiation in the silk scaffolds. Furthermore, differentiated MenSCs exhibited higher expression of TNNT2 compared with induced BMSCs. It seems that silk scaffold-seeded MenSCs could be viewed as a novel, safe, natural, and accessible construct for cardiac tissue engineering.
The present work reports the biocompatibility property of injection molded HDPE-HA-Al2O3 hybrid composites. In vitro cytocompatibility results reveal that osteogenic cell viability and bone mineralization are favorably supported in a statistically significant manner on HDPE-20% HA-20% Al2O3 composite, in comparison to HDPE-40 wt.% HA or HDPE-40 wt.% Al2O3. The difference in cytocompatibility property is explained in terms of difference in substrate wettability/surface energy and importantly, both the cell proliferation at 7 days or bone mineralization at 21 days on HDPE-20% HA-20% Al2O3 composite are either comparable or better than sintered HA. The progressive healing of cylindrical femoral bone defects in rabbit animal model was assessed by implantation experiments over 1, 4 and 12 weeks. Based on the histological analysis as well as histomorphometrical evaluation, a better efficacy of HDPE-20% HA-20% Al2O3 over high-density polyethylene (HDPE) for bone regeneration and neobone formation at host bone-implant interface was established. Taken together, the present study unequivocally establishes that despite the presence of 20% Al2O3, HDPE-based hybrid composites are as biocompatible as HA in vitro or better than HDPE in vivo.
Iron oxide magnetic nanoparticles (MNPs) can be used in targeted drug delivery systems for localized cancer treatment. MNPs coated with biocompatible polymers are useful for delivering anticancer drugs. Iron oxide MNPs were synthesized via co-precipitation method then coated with either chitosan (CS) or polyethylene glycol (PEG) to form CS–MNPs and PEG–MNPs, respectively. Arginine (Arg) was loaded onto both coated nanoparticles to form Arg–CS–MNP and Arg–PEG–MNP nanocomposites. The X-ray diffraction results for the MNPs and the Arg–CS–MNP and Arg–PEG–MNPs nanocomposites indicated that the iron oxide contained pure magnetite. The amount of CS and PEG bound to the MNPs were estimated via thermogravimetric analysis and confirmed via Fourier transform infrared spectroscopy analysis. Arg loading was estimated using UV–vis measurements, which yielded values of 5.5% and 11% for the Arg–CS–MNP and Arg–PEG–MNP nanocomposites, respectively. The release profile of Arg from the nanocomposites followed a pseudo-second-order kinetic model. The cytotoxic effects of the MNPs, Arg–CS–MNPs, and Arg–PEG–MNPs were evaluated in human cervical carcinoma cells (HeLa), mouse embryonic fibroblast cells (3T3) and breast adenocarcinoma cells (MCF-7). The results indicate that the MNPs, Arg–CS–MNPs, and Arg–PEG–MNPs do not exhibit cytotoxicity toward 3T3 and HeLa cells. However, treatment of the MCF-7 cells with the Arg–CS–MNP and Arg–PEG–MNP nanocomposites reduced the cancer cell viability with IC50 values of 48.6 and 42.6 µg/mL, respectively, whereas the MNPs and free Arg did not affect the viability of the MCF-7 cells.
This work evaluated in vivo performance of a tissue-engineered bone-like matrix obtained by culturing cell-scaffold constructs in a flow perfusion bioreactor, designed to enable culture of large constructs, envisioning the regeneration of critical-sized defects. A blend of starch with polycaprolactone scaffolds was seeded with goat bone marrow stromal cells (GBMSCs) cultured in the perfusion bioreactor for 14 days using osteogenic medium. Cell seeded scaffolds cultured in static conditions acted as controls. After 14 days, constructs (42 mm length and 16 mm in diameter) were implanted in critical size defects performed in the tibial bone of six adult goats from which the bone marrow had been collected previously. Explants were retrieved after six and 12 weeks of implantation and characterized using scanning electron microscopy, energy-dispersive spectroscopy, micro-computed tomography and radiographic analysis to assess tissue morphology and calcification. Explants were histologically analyzed, using Hematoxylin & Eosin and Masson Trichrome staining. Results provided relevant information about the performance and functionality of starch with polycaprolactone–goat bone marrow stromal cell constructs in a critical size orthotopic defect performed in a large animal model and demonstrated that culture of the starch with polycaprolactone scaffolds with the autologous cells in perfusion culture provide a good therapy for the healing and regenerative process of bone defects.
A novel decellularization method using sonication treatment is described. Sonication treatment is the combination of physical and chemical agents. These methods will disrupt cell membrane and release cell contents to external environments. The cell removal was facilitated by subsequent rinsing of sodium dodecyl sulfate detergents. Sonication treatment is used in the preparation of complete decellularized bioscaffolds. The aim of this study is to confirm the usefulness of sonication treatment for preparation of biological scaffolds. In this study, samples of aortic tissues are decellularized by sonication treatment at frequency of 170 kHz in 0.1% and 2% sodium dodecyl sulfate detergents for 10-h treatment time. The relation between decellularization and sonication parameters such as dissolved oxygen concentration, conductivity, and pH is investigated. Histological analysis and biomechanical testing is performed to evaluate cell removal efficiency as well as changes in biomechanical properties. Minimal inflammation response elicit by bioscaffolds is confirmed by xenogeneic implantation and immunohistochemistry. Sonication treatment is able to produce complete decellularized tissue suggesting that these treatments could be applied widely as one of the decellularization method.
Purpose: Ultraviolet-C irradiation on titanium implants has been recently introduced as photofunctionalization to enhance osseointegration, which possibly also provide anti-microbial function to titanium surface as with photocatalyst. The purpose of this study was to determine the effect of ultraviolet-C pre-irradiation to various topographical titanium surfaces on the attachment or biofilm formation of wound pathogens in comparison with that of ultraviolet-A pre-irradiation, with consideration for the physicochemical mechanism.
Materials and methods: The amount of wound pathogens such as Staphylococcus aureus or Streptococcus pyogenes on titanium disks with mirror-polished, turned, acid-etched, or shot-blasted surfaces with or without 500 J/cm2 ultraviolet-A or ultraviolet-C pre-irradiation for 8 h incubation in brain heart infusion broth was evaluated by fluorescence microscopic quantification with 5-cyano-2, 3-ditolyl-2 H-tetrazolium chloride staining for viable bacteria. The surface roughness, wettability, and atomic composition of the surface were evaluated before and after ultraviolet-A or ultraviolet-C irradiation.
Results: Regardless of topographies, the amount of bacterial attachment and accumulation was lower on ultraviolet-C pre-irradiated surfaces than on the non-irradiated surface through 8 h incubation. The reducing effect of bacterial accumulation on the roughened surfaces by ultraviolet-A pre-irradiation was inferior to that by ultraviolet-C. Despite no effect on surface topography, ultraviolet-C irradiation changed wettability to superhydrophilicity and reduced carbon contents on any titanium surface with a greater degree than those by ultraviolet-A irradiation.
Conclusion: Ultraviolet-C irradiation reduced the attachment and biofilm formation of wound pathogens on various topographical titanium surfaces, rivaling or surpassing UVA irradiation in degree. The mechanism might involve superhydrophilicity and carbon elimination on the surface.
This article investigates the in-vitro biocompatibility and corrosion behaviour of strontium ion incorporated TiO2 nanotube arrays formed by anodization method for orthopaedic applications. The morphological studies were carried out using field emission scanning electron microscopy, atomic force microscopy, attenuated total reflectance fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy and thin film X-ray diffraction techniques. The morphological investigation indicated that the length and the average diameter of nanotube were 2.1 ± 0.3 µm and 110 ± 4 nm, respectively. The wettability measurements showed that the TiO2 nanotube arrays have super wettability, as well as, strontium ion incorporated TiO2 nanotube arrays exhibited hydrophilic behaviour. Excellent in-vitro bioactivity was observed for TiO2 nanotube arrays with strontium ions. Electrochemical studies in Hank’s solution showed that the TiO2 nanotube arrays with strontium ions have enhanced corrosion resistance.
pH-sensitive liposomes are designed to undergo acid-triggered destabilization. In the present study, we prepared polymer-modified, plasma stable, pH-sensitive fusogenic mitoxantrone liposomes to increase efficacy and selectivity on cancer cell lines. Conventional liposomes were prepared using cholesterol and dipalmitoyl-sn-glycero-3-phosphatidylethanolamine. Dioleoylphosphatidylethanolamine and a cholesteryl derivative, poly(monomethylitaconate)-co-poly(N,N-dimethylaminoethyl methacrylate) (PMMI-co-PDMAEMA), were used for the preparation of pH-sensitive fusogenic liposomes. Using polyethylene glycol (PEG)-poly(monomethylitaconate)-CholC6 (PEG-PMMI-CholC6) copolymers instead of cholesterol introduced pH-sensitive and plasma stability properties simultaneously in prepared liposomes. All formulations were prepared by thin film hydration method and subsequently, pH-sensitivity and stability in human serum were evaluated. The ability of pH-sensitive fusogenic liposomes to enhance the mitoxantrone cytotoxicity and selectivity in cancerous cell lines was assessed in vitro compared to normal cell line using human breast cancer cell line (MCF-7), human prostate cancer cell line (PC-3), and human umbilical vein endothelial cells line. Results revealed that both PMMI-co-PDMAEMA and PEG-PMMI-CholC6-based formulations showed pH-sensitive property and were found to rapidly release mitoxantrone under mildly acidic conditions. Nevertheless, only the PEG-PMMI-CholC6-based liposomes preserved pH-sensitivity after incubation in plasma. Mitoxantrone loaded-pH-sensitive fusogenic liposomes exhibited a higher cytotoxicity than the control conventional liposomes on MCF-7 and PC-3 cell lines. On the contrary, both pH-sensitive fusogenic liposomes showed lower cytotoxic effect on human umbilical vein endothelial cell line. Plasma stable, pH-sensitive fusogenic liposomes are promising carriers for enhancing the efficiency and selectivity, besides reduction of the side effects of anticancer agents.
Bone tissue engineering, which relies on the interactions between stem cells and suitable scaffold materials, represents a highly desirable alternative to currently used allograft or autograft strategies for the treatment of bone defects caused by injury or disease, with one of the major challenges being to generate sufficient quantities of stem cells to bring about the intended therapeutic effect. However, conventional cell culture to achieve sufficient cell numbers faces limitations of low efficiency and diminished efficacy of stem cells due to repeated passaging. Furthermore, current microcarriers available may not be suitable for therapeutic implantation. Here, the authors featured an apatite-based microcarrier intended for bone tissue engineering applications. These apatite microcarriers have a diameter of ~230 µm, and exhibited porous and rough surface morphology. Peaks obtained from X-ray diffractometry (XRD) corresponded to hydroxyapatite (HA) with high crystallinity. Fourier transform infrared spectrophotometry (FTIR) showed that no residues of alginate remained, and all bands observed belong to phosphate and hydroxyl groups of HA. To evaluate the cytocompatibility of these microcarriers, in vitro proliferation studies were conducted and compared with conventional monolayer as well as Cytodex 3. The authors found that human foetal mesenchymal stem cells (hfMSCs) cultured on apatite microcarriers exhibited comparable growth characteristics, achieving 1.4-fold higher live cells than Cytodex 3 over a 9-day culture period. As these microcarriers were hypothesised to offer enhanced osteogenic potency over conventional monolayer culture, alkaline phosphatase (ALP), type I collagen and osteocalcin expression of hfMSCs cultured on the apatite microcarriers were evaluated over a 12-day period. ALP expression for hfMSCs seeded on apatite microcarriers was 2.7-fold higher than that of adherent monolayer culture (p < 0.001). Additionally, type I collagen and osteocalcin expression were 1.8- and 1.5-fold higher than that of adherent monolayer culture on day 12, respectively (p < 0.001).
Purpose: The objective of this study was to investigate the therapeutic potential of poly(lactic-co-glycolic acid) (PLGA) microspheres loaded with recombinant human growth and differentiation factor-5 (rhGDF-5) on the disc degeneration induced by needle puncture in a rat caudal disc model.
Methods:The rhGDF-5-loaded PLGA microspheres were prepared by the water-oil-water double-emulsion solvent evaporation method, and release kinetics was determined over 42 days. Rats that underwent 21-G needle puncture at rat tail discs were injected with rhGDF-5/PLGA microspheres at four weeks after needle injury. At eight weeks after the injection, disc height, glycosaminoglycans content, and DNA content of the discs were evaluated. In addition, gene expression analysis of aggrecan, collagen type I, and collagen type II in the rat nucleus pulposus was measured by real-time polymerase chain reaction. Rat discs were also assessed by histology using hematoxylin and eosin stain.
Results: Encapsulation of rhGDF-5 in PLGA microspheres guaranteed a sustained release of active rhGDF-5 for more than 42 days. The injection of GDF-5/PLGA microspheres resulted in a statistically significant restoration of disc height (p < 0.01), improvement of sulfated glycosaminoglycan (p < 0.05), DNA content (p < 0.05), and significantly increased mRNA levels of collagen type II (p < 0.01), and the differentiation index (the ratio of collagen type II to collagen type I, p < 0.01). In addition, rhGDF-5/PLGA microspheres treatment also improved histological changes induced by needle puncture.
Conclusions: The results of this study suggest that injection of rhGDF-5 loaded in PLGA microspheres into rat tail discs may be as a promising therapy strategy to regenerate or repair the degenerative disc.
An adequate cell seeding technique is essential for effective bone regeneration on cell seeded constructs of porous tricalcium phosphates. In previous studies, dynamic cell seeding, in which an external force is applied to seed cells on a biomaterial, resulted in more homogeneous cell seeding in low porosity scaffolds than static seeding. The optimal cell seeding technique for high porosity scaffolds has not been defined yet. Human mesenchymal stem cells were isolated from bone marrow and characterized. The cells were seeded on low porosity (45%) and high porosity (90%) tricalcium phosphate scaffolds using a static and a vacuum seeding technique. LIVE/DEAD® staining of the cell-scaffold complexes followed by confocal laser scanning microscopy was used to measure cell proliferation, cell distribution and cell viability one, three and seven days after seeding. Cell proliferation was also quantified using a DNA quantification assay. Neither static nor vacuum seeding resulted in homogeneous cell seeding on both low and high porosity scaffolds. Cell density was lower on the inside than on the outside of the scaffolds. On low porosity scaffolds, the vacuum method yielded the highest numbers of cells compared to the static method. Low porosity scaffolds were seeded most homogeneously using the static seeding method. Seven days after seeding, numbers of adherent cells were comparable for both scaffold types and independent of the cell seeding technique used. In conclusion, on high porosity scaffolds, static seeding results in more homogeneous cell seeding and it is easier to use than a vacuum seeding technique.
In this study, we evaluated the effect of poly(vinylidene fluoride-trifluoroethylene)/barium titanate (P(VDF-TrFE)/BT) membrane on in vivo bone formation. Rat calvarial bone defects were implanted with P(VDF-TrFE)/BT and polytetrafluoroethylene (PTFE) membranes, and at 4 and 8 weeks, histomorphometric and gene expression analyses were performed. A higher amount of bone formation was noticed on P(VDF-TrFE)/BT compared with PTFE. The gene expression of RUNX2, bone sialoprotein, osteocalcin, receptor activator of nuclear factor-kappa B ligand, and osteoprotegerin indicates that P(VDF-TrFE)/BT favored the osteoblast differentiation compared with PTFE. These results evidenced the benefits of using P(VDF-TrFE)/BT to promote new bone formation, which may represent a promising alternative to be employed in guided bone regeneration.
Chest-wall invading malignancies usually necessitate the resection of the respective part of the thoracic wall. Gore-Tex® is the material of choice that is traditionally used to repair thoracic defects. This material is well accepted by the recipient; however, though not rejected, it is an inert material and behaves like a ‘foreign body’ within the thoracic wall. By contrast, there are materials that have the potential to physiologically integrate into the host, and these materials are currently under in vitro and also in vivo investigation. These materials offer a gradual but complete biodegradation over time, and severe adverse inflammatory responses can be avoided. Here, we present a novel material that is a biodegradable nanocomposite based on poly-lactic-co-glycolic acid and amorphous calcium phosphate nanoparticles in comparison to the traditionally employed Gore-Tex® being the standard for chest-wall replacement. On a mouse model of thoracic wall resection, that resembles the technique and localization applied in humans, poly-lactic-co-glycolic acid and amorphous calcium phosphate nanoparticles and Gore-Tex® were implanted subcutaneously and additionally tested in a separate series as a chest-wall graft. After 1, 2, 4 and 8 weeks cell infiltration into the respective materials, inflammatory reactions as well as neo-vascularization (endothelial cells) were determined in six different zones. While Gore-Tex® allowed for cell infiltration only at the outer surface, electrospun poly-lactic-co-glycolic acid and amorphous calcium phosphate nanoparticles were completely penetrated by infiltrating cells. These cells were composed mainly by macrophages, with only 4% of giant cells and lymphocytes. Total macrophage count increased by time while the number of IL1-β–expressing macrophages decreased, indicating a protective state towards the graft. As such, poly-lactic-co-glycolic acid and amorphous calcium phosphate nanoparticles seem to develop ideal characteristics as a material for chest-wall replacement by (a) having the advantage of full biodegradation, (b) displaying stable chest-wall structures and (c) adapting a physiological and integrating graft compared to Gore-Tex®.
To improve bone engineering for clinical applications, we coupled nanofiber-peptide hydrogel to nano-hydroxyapatite/collagen to form a bioactive scaffold (cnHAC) that mimics extracellular matrices. In comparison to nano-hydroxyapatite/collagen, we found that cnHAC promoted cell adhesion and spreading, and DNA content measurements, alkaline phosphatase activity assays, and reverse transcriptase-polymerase chain reaction analyses of osteogenic gene expression showed that cnHAC significantly improved cellular attachment, proliferation, and osteogenic differentiation in vitro (P < 0.05). In vivo models based on rat calvarial implants showed that cnHAC significantly enhanced bone regeneration (P < 0.05). In conclusion, we demonstrated that novel cnHAC scaffolds could potentially facilitate future bone regenerative medicine.
Advances in electrospun nanofibres with bioactive materials have enhanced the scope of fabricating biomimetic scaffolds for tissue engineering. The present research focuses on fabrication of polycaprolactone/aloe vera/silk fibroin nanofibrous scaffolds by electrospinning followed by hydroxyapatite deposition by calcium-phosphate dipping method for bone tissue engineering. Morphology, composition, hydrophilicity and mechanical properties of polycaprolactone/aloe vera/silk fibroin–hydroxyapatite nanofibrous scaffolds along with controls polycaprolactone and polycaprolactone/aloe vera/silk fibroin nanofibrous scaffolds were examined by field emission scanning electron microscopy, Fourier transform infrared spectroscopy, contact angle and tensile tests, respectively. Adipose-derived stem cells cultured on polycaprolactone/aloe vera/silk fibroin–hydroxyapatite nanofibrous scaffolds displayed highest cell proliferation, increased osteogenic markers expression (alkaline phosphatase and osteocalcin), osteogenic differentiation and increased mineralization in comparison with polycaprolactone control. The obtained results indicate that polycaprolactone/aloe vera/silk fibroin–hydroxyapatite nanofibrous scaffolds have appropriate physico-chemical and biological properties to be used as biomimetic scaffolds for bone tissue regeneration.
Thermal burns typically display an injury pattern dictated by the transfer of the thermal energy into the skin and underlying tissues and creation of three zones of injury represented by a necrotic zone of disrupted cells and tissue, an intermediate zone of injured and dying cells, and a distant zone of stressed cells that will recover with proper treatment. The wound healing capabilities of a keratin biomaterial hydrogel were studied in two pilot studies, one using a chemical burn model in mice and the other a thermal burn model in swine. In both studies, keratin was shown to prevent enlargement of the initial wound area and promote faster wound closure. Interestingly, treating thermally stressed dermal fibroblast in culture demonstrated that soluble keratin was able to maintain cell viability and promote proliferation. Separation of so-called alpha and gamma fractions of the keratin biomaterial had differential effects, with the gamma fraction producing more pronounced cell survival and recovery. These results suggest that the gamma fraction, composed essentially of degraded alpha keratin proteins, may facilitate cell rescue after thermal injury. Treatment of burns with gamma keratin may therefore represent a potential therapy for wounds with an intermediate zone of damaged tissue that has the potential to contribute to spontaneous healing.
In recent years, there has been increasing interest for the surface modification of biomaterials in order to improve their surface properties. The bare metal stents surface based on 3-dimethyl(methacryloyloxyethyl)ammonium propane sulfonate polymers has shown an excellent antifouling and blood compatibility by using surface-initiated atom transfer radical polymerization. Surface structure, morphology, wettability, and element content were characterized by scanning electronic microscope, static water contact angles measurement, X-ray photoelectron spectroscopy measurement, respectively. The results showed zwitterionic brushes were successfully fabricated on bare metal stents. The blood compatibility of bare metal stents before and after modification was evaluated by platelet adhesion tests, hemolysis assay, morphological changes of red blood cells, coagulation time tests, plasma recalcification time assay, complement activation, and platelet activation at molecular level. Moreover, the cytotoxicity was also to be characterized. All assays showed after the modification with zwitterionic brush the metal stents displayed a property of excellent blood compatibility and low cytotoxicity.
Gastrointestinal endoscopy is a standard diagnostic tool for gastrointestinal ulcers and cancer. In this study, we have developed recombinant human epidermal growth factor-containing ulcer-coating polymeric sol–gel for endoscopic application. Chitosan and pluronic F127 were employed for their thermoresponsive and bioadhesive properties. At temperatures below 21℃, polymeric sol–gel remains liquid during endoscopic application and transforms to gel at body temperature after application on ulcers. In an in vitro cellular wounding assay, recombinant human epidermal growth factor sol–gel significantly enhanced the cell migration and decreased the wounding area (68%) compared to nontreated, recombinant human epidermal growth factor solution, and sol–gel without recombinant human epidermal growth factor (42, 49, and 32 % decreased at day 1). The in vivo ulcer-healing study was performed in an acetic acid-induced gastric ulcer rat model and proved that our recombinant human epidermal growth factor endoscopic sol–gel facilitated the ulcer-healing process more efficiently than the other treatments. Ulcer sizes in the recombinant human epidermal growth factor sol–gel group were decreased 2.9- and 2.1-fold compared with those in the nontreated group on days 1 and 3 after ulceration, respectively. The mucosal thickness in the recombinant human epidermal growth factor sol–gel group was significantly increased compared to that in the nontreated group (3.2- and 6.9-fold on days 1 and 3 after ulceration, respectively). In a gastric retention study, recombinant human epidermal growth factor sol–gel stayed on the gastric mucosa more than 2 h after application. The present study suggests that recombinant human epidermal growth factor sol–gel is a prospective candidate for treating gastric ulcers via endoscopic application.
Poly-4-hydroxybutyrate, P(4HB), is a biosynthetic thermoplastic polymer that has been studied as a bio-absorbable medical material. In order to explore the in vivo biodegradation behaviour of porous P(4HB) membranes with specified apertures (89–150 µm), membranes with different porosities were implanted subcutaneously into the backs of 27 eight-week-old Sprague Dawley® rats. The implanted specimens were examined with Masson and hematoxylin and eosin staining. Masson staining indicated that the P(4HB) membranes were encased in fibrous cysts and that more collagen fibers were present within the sections of the hyper-porosity group. Hematoxylin and eosin staining showed that the residual area of the P(4HB) membranes in the hyper-porosity group decreased sharply compared to the hypo-porosity group, which implied that the P(4HB) membranes with higher porosity degraded faster than those with lower porosity. A slow degradation phase persisted for approximately 14 weeks during the degradation process. After the 16th week, the P(4HB) scaffolds fell into a fast degradation phase. The residual areas of the hyper-porosity P(4HB) membranes at the 32nd week were reduced by 39.76% compared with the second week after implantation. We concluded that P(4HB) membranes manifest a special biodegradation behavior in vivo and that the increased porosity of these membranes is an important factor favoring their biodegradation rates.
Group II–VI semiconductor quantum dots (Q-dots) have found various applications in biomedical field during last decade. In this study, we have synthesized CdSe Q-dots and CdSe/ZnS core/shell (CS) by wet chemical route and characterized using X-ray diffraction (XRD), transmission electron microscopy (TEM), dynamic light scattering (DLS), Fourier-transform infrared spectroscopy (FT-IR) and Photoluminescence (PL) spectroscopy. CS formation was confirmed by red shift as well as enhancement in the luminescence peak compared to bare Q-dots. Processing parameters such as core and sulfur concentrations were optimized at maximum luminescence efficiency during the shell preparation. Effects of dialysis, aging and cell culture medium on the properties of the Q-dots and CS were also studied by luminescence and DLS techniques. DLS data showed Q-dots and CS to be stable, and there was no effect on the integrity of the Q-dots and CS after various modifications. CS was found to be hemocompatible and cytocompatible for human umbilical vein endothelial cells even at a high concentration of 0.1 mg/ml up to 48 h indicating high potential for CS in various biomedical applications.
Poly(glycerol sebacate) (PGS) and poly(xylitol sebacate) (PXS) are biodegradable elastomers with tremendous potential in soft tissue engineering. This study was aimed at exploring the enzymatic degradation mechanisms of these polyesters, using biochemical conditions similar to those occurring in vivo. To this end, PGS and PXS (crosslinked at 130°C for 2 or 7 (PGS)/12 days (PXS)) were incubated in vitro under physiological conditions in tissue culture media supplemented with either a biodegrading enzyme (esterase), an oxidant species (FeSO4/H2O2 with 0.11 molar ratio of Fe2+/H2O2), an oxidant generating enzyme (xanthine oxidase and xanthine) or combinations of these (FeSO4/H2O2 and esterase, or (v) xanthine oxidase/xanthine and esterase), based on their independent effects on polymer degradation. Testing was performed over 35 days of continuous incubation, during which mechanical properties, mass loss, biomaterial thickness and pH value of the culture medium were determined. Degradation kinetics of both PGS and PXS samples were primarily determined by the degree of crosslink density. Esterase and FeSO4/H2O2 accelerated the degradation of both polymers, by promoting hydrolysis and free-radical degradation, although this action was not affected by the presence of xanthine oxidase and xanthine. Degradation of PGS and PXS is primarily mediated by the action of esterase, with free-radical oxidation playing a secondary role, suggesting that both could synergistically affect the biodegradability of biomaterial implants, under more complex biological conditions.
Soy protein is emerging as a novel material for biomedical applications due to its abundance in nature, ease of isolation and processing, and inherent properties for mediating cell adhesion and growth. In this study, mechanically robust soy protein hydrogels were fabricated with varying weight percentages in water (15, 18, and 20 wt.%) without the use of chemical modifiers or crosslinkers. This fabrication method is beneficial because it allows for the direct injection of these soy hydrogels in vivo. The material properties, drug releasing capability, and biocompatibility in vitro and in vivo were assessed. The different concentrations of soy protein varied the rheological, swelling, and mechanical properties and affected the release of the model drug fluorescein from the hydrogels in vitro. Higher weight percent of soy increased the robustness of the hydrogels and released a lower amount of fluorescein over one week. Viability and growth of seeded L929 mouse fibroblasts demonstrated that the hydrogels were biocompatible in vitro for one week. Soy hydrogels were injectable in vivo into the subcutaneous pocket of mice, and histological staining showed minimal fibrous capsule formation for up to 20 days. The ease of fabrication and tailorable properties of soy hydrogels render it a promising biomaterial for tissue engineering and drug delivery applications, particularly for wound healing.
Objective: We sought to determine the patency of normal arterial branches from the covered segments of an artery after stenting.
Background: Most intracranial aneurysms occur at arterial branching points (bifurcations, side-branches, or perforators). The post-stenting patency of normal arterial branches from the covered segments of the artery is important. We have previously developed a hybrid stent with micropores to prevent early parent artery occlusion by more early endothelialization, and mid- to long-term parent artery stenosis by control of intimal hyperplasia after aneurysm occlusion.
Methods: We created aneurysms in 10 rabbits by distal ligation and intraluminal incubation of elastase within an endovascularly trapped proximal segment of the common carotid artery. All animals were treated with hybrid stents having micropores. Four animals were observed for one month and three each for three and 12 months. The patency of the side-branches of the subclavian artery was evaluated angiographically and in some cases, histologically.
Results: Aneurysms were completely occluded at all time points other than 12 months. The subclavian artery and brachiocephalic artery were patent, without significant stenosis. All the side-branches of the subclavian artery detected on the preoperative angiogram remained patent at the final assessment.
Conclusion: The use of hybrid stents for aneurysm repair and side-branch patency seems to be effective, as per the long-term results obtained in an animal model.
The aim of the present study was to fabricate mineralized polycaprolactone nanofibrous scaffold and investigate its ability to elicit odontogenic differentiation of human dental pulp cells, compared to the pure polycaprolactone scaffold. Polycaprolactone nanofibrous scaffold was produced by electrospinning, and the surface was mineralized with apatite. Cellular behaviors on the mineralized polycaprolactone scaffold were assessed in terms of cell adhesion, growth, and odontoblastic differentiation. To evaluate the signal transduction of human dental pulp cells, mRNA expression was analyzed and Western blotting was performed. Mineralized polycaprolactone showed improved cell proliferation, mineralized nodule formation, and expression of odontoblastic marker genes including alkaline phosphatase, osteopontin, osteocalcin, dentin sialophosphoprotein (DSPP), and dentin matrix protein-1, as compared with pure polycaprolactone. Although the cell adhesion on the mineralized polycaprolactone was similar to that of the polycaprolactone, the expression level of proteins including collagen type I and the key adhesion receptor (integrin components α1, α2, and β1) was upregulated in mineralized polycaprolactone compared to polycaprolactone. Especially, cells seeded onto mineralized polycaprolactone scaffolds showed significantly increased levels of phosphorylated focal adhesion kinase, a marker of integrin activation, and downstream pathways, such as phosphor (p)-Akt, p-extracellular signal regulated kinase, p-c Jun N-terminal kinase, nuclear factor-kappa B, c-fos, and c-jun, compared with pure polycaprolactone. The mineralized polycaprolactone scaffold is attractive for dentin tissue engineering by promoting growth and odontogenic differentiation of human dental pulp cells through the integrin-mediated signaling pathway.
Novel microcarriers consisting of calcium phosphate cement and alginate were prepared for use as three-dimensional scaffolds for the culture and expansion of cells that are effective for bone tissue engineering. The calcium phosphate cement-alginate composite microcarriers were produced by an emulsification of the composite aqueous solutions mixed at varying ratios (calcium phosphate cement powder/alginate solution = 0.8–1.2) in an oil bath and the subsequent in situ hardening of the compositions during spherodization. Moreover, a porous structure could be easily created in the solid microcarriers by soaking the produced microcarriers in water and a subsequent freeze-drying process. Bone mineral-like apatite nanocrystallites were shown to rapidly develop on the calcium phosphate cement–alginate microcarriers under moist conditions due to the conversion of the α-tricalcium phosphate phase in the calcium phosphate cement into a carbonate–hydroxyapatite. Osteoblastic cells cultured on the microspherical scaffolds were proven to be viable, with an active proliferative potential during 14 days of culture, and their osteogenic differentiation was confirmed by the determination of alkaline phosphatase activity. The in situ hardening calcium phosphate cement–alginate microcarriers developed herein may be used as potential three-dimensional scaffolds for cell delivery and tissue engineering of bone.
Objective: The purpose of this study was to determine whether the platelet-rich plasma–agarose gel scaffold could be a bioactive scaffold capable of growth factors release for cartilage repair.
Methods: Porcine chondrocytes were seeded in agarose gel and platelet-rich plasma–agarose gel. During the 28-days culture, microstructure of hydrogels and morphologies of chondrocytes seeded in the hydrogels were observed using scanning electron microscope; viability of chondrocytes in gels was examined by live/dead assay; qualitative and quantitative analysis of glycosaminoglycan, collagen and DNA were assessed by histological, immunohistochemcial staining and biochemical assay; gene expression was measured by real-time polymerase chain reaction. In vitro cartilage ring models were used to evaluate the integration of the scaffolds, and the integration strength was analyzed by mechanical push-out tests.
Results: Scanning electron microscope revealed both scaffolds had highly uniform porous structure. Live/dead scaffolds showed 100% cells alive in both groups. After 28-days culture, glycosaminoglycan, collagen, DNA content and chondrocyte-related genes expression in platelet-rich plasma–agarose gel were significantly higher than pure agarose gel. Integration strength in platelet-rich plasma–agarose gel was also higher compared to pure agarose gel.
Conclusion: Platelet-rich plasma showed a positive effect on chondrocytes proliferation, differentiation and integration between native cartilage and engineered tissue when combined with agarose gel. Our findings suggest that platelet-rich plasma–agarose gel scaffold is a promising bioactive scaffold for future cartilage tissue engineering and future clinical works.
Sternotomy and sternal closure occur prior to and post cardiac surgery, respectively. Although post-operative complications associated with poor sternal fixation can result in morbidity, mortality, and considerable resource utilization, sternotomy is preferred over other methods such as lateral thoracotomy. Rigid sternal fixation is associated with stability and reduced incidence of post-operative complications. This is a comprehensive review of the literature evaluating in vivo, in vitro, and clinical responses to applying commercial and experimental surgical tools for sternal fixation after median sternotomy. Wiring, interlocking, plate-screw, and cementation techniques have been examined for closure, but none have experienced widespread adoption. Although all techniques have their advantages, serious post-operative complications were associated with the use of wiring and/or plating techniques in high-risk patients. A fraction of studies have analyzed the use of sternal interlocking systems and only a single study analyzed the effect of using kryptonite cement with wires. Plating and interlocking techniques are superior to wiring in terms of stability and reduced rate of post-operative complications; however, further clinical studies and long-term follow-up are required. The ideal sternal closure should ensure stability, reduced rate of post-operative complications, and a short hospitalization period, alongside cost-effectiveness.
The purpose of this study was to develop a specific targeting magnetic nanoparticle probe for magnetic resonance imaging and therapy in the form of local hyperthermia. Carboxymethyl dextran–coated ultrasmall superparamagnetic iron oxide nanoparticles with carboxyl groups were coupled to cyclic arginine-glycine-aspartic peptides for integrin αvβ3 targeting. The particle size, magnetic properties, heating effect, and stability of the arginine-glycine-aspartic–ultrasmall superparamagnetic iron oxide were measured. The arginine-glycine-aspartic–ultrasmall superparamagnetic iron oxide demonstrates excellent stability and fast magneto-temperature response. Magnetic resonance imaging signal intensity of Bcap37 cells incubated with arginine-glycine-aspartic–ultrasmall superparamagnetic iron oxide was significantly decreased compared with that incubated with plain ultrasmall superparamagnetic iron oxide. The preferential uptake of arginine-glycine-aspartic–ultrasmall superparamagnetic iron oxide by target cells was further confirmed by Prussian blue staining and confocal laser scanning microscopy.
This study compared the metabolic activity, cell proliferation and osteogenic differentiation of human adipose-derived stromal/stem cells cultured on four different scaffolds (poly--caprolactone, akermanite:poly--caprolactone composites, akermanite and β-tricalcium phosophate) with or without osteogenic media supplementation for up to 21 days. The hypothesis was that human adipose-derived stromal/stem cells osteogenesis in akermanite-containing scaffolds would be greater than the other scaffold types independent of the media supplementation. According to the results, human adipose-derived stromal/stem cells loaded on different scaffolds and cultured in both media conditions displayed significant changes in the metabolic activity and cell proliferation. After 21 days of culture in osteogenic medium, the human adipose-derived stromal/stem cells loaded onto akermanite-based scaffolds had greater calcium deposition and osteocalcin expression relative to human adipose-derived stromal/stem cells loaded onto β-tricalcium phosophate and poly--caprolactone. In vivo investigations are needed to further assess the bone tissue engineering potential of human adipose-derived stromal/stem cells loaded to akermanite:poly--caprolactone composites.
Over the last few years, alloplastic bone substitute materials are raising much interest as an alternative to autologic transplants and xenogenic materials especially in oral surgery. These non-immunogenic and completely resorbable biomaterials are becoming the basis for complete and predictable guided bone regeneration in many cases. The objective of our research was to evaluate the dynamics of bone formation in rats’ skulls after implantation of the new chitosan/tricalcium phosphate/alginate biomaterial in comparison to the commercially available alloplastic bone graft. A total of 45 adult male rats weighing 300–400 g were used for the study. The 85-mm-diameter defects in calvaria bone were prepared with a trephine bur, and then filled with the bone substitute materials: chitosan/tricalcium phosphate/alginate or easy-graft Classic (Degradable Solutions AG) (EA) or left just with the blood clot. Animals were sacrificed at 1 and 3 months for histological, histomorphometrical and micro-tomographic evaluations. Histological evaluation at 1 month showed early new bone formation, observed around the experimental biomaterial (CH/TCP/Alg). There were no features of purulent inflammation and necrosis or granulomatous inflammation. Microscopic examination after 3 months following the surgery revealed trabecular bone formation around chitosan-based bone graft with no significant inflammatory response. Less satisfactory and differing results were observed for the commercially available EA and control blood clot. The tested material (chitosan) showed a high degree of biocompatibility and osteoconductivity in comparison with the control groups. Additionally, it seemed to be a "user-friendly" material for oral surgeons.
Herein we report a facile layer-by-layer method for creating an antimicrobial coating composed of silver nanoparticles on medical grade titanium test discs. Nanoscale silver nanoparticle layers are attached to the titanium orthopedic implant material via aminopropyltriethoxy silane crosslinker that reacts with neighboring silane moieties to create an interconnected network. A monolayer of silane, followed by a monolayer of silver nanoparticles would form one self-assembled layer and this process can be repeated serially, resulting in increased silver nanoparticles deposition. The release rate of silver ion increases predictably with increasing numbers of layers and at appropriate thicknesses these coatings demonstrate 3–4 log reduction of viable Escherichia coli and Staphylococcus aureus bacteria. Increasing the thickness of the coatings resulted in reduced bacterial colonization as determined by fluorescent staining and image analysis. Interestingly, the cytotoxicity of murine 3T3 cells as quantified by fluorescent staining and flow cytometry, was minimal and did not vary significantly with the coating thickness. Additionally, these coatings are mechanically stable and resist delamination by orthogonal stress test. This simple layer-by-layer coating technique may provide a cost-effective and biocompatible method for reducing microbial colonization of implantable orthopedic devices.
To examine the effect of scaffold pore size on bone regeneration within hydroxyapatite scaffolds in large segmental defects, this study evaluated two porous interconnected architectures having similar porosity and strut thickness but different pore sizes. Using a 10 mm segmental rabbit radius defect model, a bilayer scaffold architecture mimicking the cortical-cancellous organization of bone (pore size 200 µm outer layer, 450 µm inner layer) was compared to a purely trabecular-like architecture (pore size 340 µm) and an untreated defect. Bone regeneration was measured using micro-computed tomography and histology after four and eight weeks of in vivo implantation, and the mechanical strength of the defect site after eight weeks’ implantation was assessed using flexural testing. Although both bilayer and trabecular architectures promoted bone growth, the trabecular scaffolds were observed to have more uniform new bone distribution within the scaffold interior at four weeks and greater bone regeneration overall after eight weeks’ implantation (149 ± 9 mm3 compared to 121 ± 8 mm3 in the bilayer and 66 ± 14 mm3 in the defect). Additionally, the trabecular scaffolds were observed to exhibit significantly greater flexural strength (124% increase) and toughness (388% increase) when compared to the empty defects after eight weeks’ implantation. It was concluded from this study that a larger uniform pore size led to greater functional bone regeneration over a longer implantation period for large segmental defects.
Objective: Cartilage repair of full-thickness chondral defects in the knees of Goettinger minipigs was assessed after treatment with cell-free collagen type-I gel with or without additional BMP-7 loaded poly(lactic-co-glycolid acid) microspheres.
Methods: Two full-thickness chondral defects were created in the trochlear groove of one hind leg knee in six Goettinger minipigs. Six defects were treated with a cell-free collagen type-I gel plug of 10 mm, the corresponding six defects were treated with a cell-free collagen type-I plug with poly(lactic-co-glycolid acid) microspheres loaded with recombinant BMP-7 (100 ng/ml gel). After 1 year, the animals were sacrificed. Immediately after recovery, non-destructive biomechanical testing was performed. The repair tissue quality was evaluated by immunohistochemistry and the O’Driscoll score was calculated.
Results: After 1 year, a robust cellular migration into the cell-free collagen gel plugs occurred and a hyaline-like repair tissue was found. Collagen type-II production and cellular organisation were higher in the BMP-7 microsphere group. The determination of the E-modulus, creep and relaxation revealed that mechanical properties of the BMP-7 microsphere group in summary were closer to control hyaline cartilage.
Conclusions: While all specimens revealed a homogeneous cellular distribution, ECM production, cellular organisation and mechanical properties were enhanced by continuous BMP-7 release.
Titanium framework keratoprosthesis has been commonly used in the severe corneal blindness, but the tissue melting occurred frequently around titanium. Since hydroxyapatite has been approved to possess a good tissue integration characteristic, nanostructured hydroxyapatite was coated on the surface of titanium through the aerosol deposition method. In this study, nanostructured hydroxyapatite coating was characterized by X-ray diffraction, scanning electron microscopy, atomic force microscopy, and auger electronic spectrometer. Biological evaluations were performed with rabbit cornea fibroblast in vitro and an animal model in vivo. The outcomes showed the coating had a grain-like surface topography and a good atomic mixed area with substrate. The rabbit cornea fibroblasts appeared a good adhesion on the surface of nanostructured hydroxyapatite in vitro. In the animal model, nanostructured hydroxyapatite-titanium implants were stably retained in the rabbit cornea, and by contrast, the corneal stroma became thinner anterior to the implants in the control. Therefore, our findings proved that nanostructured hydroxyapatite-titanium could not only provide an improved bond for substrate but also enhance the tissue integration with implants in host. As a promising material, nanostructured hydroxyapatite-titanium–based keratoprosthesis prepared by the aerosol deposition method could be utilized for the corneal blindness treatment.
Highly oriented poly(lactic acid) (PLA)/multi-walled carbon nanotubes (MWNTs) composites were fabricated through solid hot drawing technology in an effort to improve the mechanical properties and blood biocompatibility of PLA as blood-contacting medical devices. It was found that proper MWNTs content and drawing orientation can improve the tensile strength and modulus of PLA dramatically. With the increase in draw ratio, the cold crystallization peak became smaller, and the glass transition and the melting peak of PLA moved to high temperature, while the crystallinity increased, and the grain size decreased, indicating the stress-induced crystallization of PLA during drawing. MWNTs showed a nucleation effect on PLA, leading to the rise in the melting temperature, increase in crystallinity and reduction of spherulite size for the composites. Moreover, the intensity of (002) diffraction of MWNTs increased with draw ratio, indicating that MWNTs were preferentially aligned and oriented during drawing. Microstructure observation demonstrated that PLA matrix had an ordered fibrillar bundle structure, and MWNTs in the composite tended to align parallel to the drawing direction. In addition, the dispersion of MWNTs in PLA was also improved by orientation. Introduction of MWNTs and drawing orientation could significantly enhance the blood compatibility of PLA by prolonging kinetic clotting time, reducing hemolysis ratio and platelet activation.
Stent-grafts externally fitted with a Z-shaped stents were compared to devices fitted with ringed stents in an in vitro oscillating fatigue machine at 200 cycles per minute and a pressure of 360 mmHg for scheduled durations of up to 1 week. The devices fitted with Z-stents showed a considerably lower endurance limit to buckling compared to the controls. The contact between the apexes of adjacent Z-stents resulted in significant damage to the textile scaffolds and polyester fibers due to the sharp angle of the Z-stents. The ringed stents did not cause any fraying in the textile scaffolds.
Hydroxyapatite (HA)/poly-l-lactide(PLLA) composite biomaterials are available for orthopedic applications, but bioresorption and cell-mediated inflammation in bone cortex are unknown. We conducted an 84-month follow-up study with Beagle dogs that were subjected to implants with either PLLA (left femur) or HA/PLLA (right femur). Histological and radiographic analysis showed that HA/PLLA screws induced significant increases in HA content from 36 months onward and complete burr hole closure at 60 months, whereas PLLA screws did not. Moreover, PLLA screws induced more severe fibrous tissue and histiocyte infiltration. HA/PLLA screws promote earlier burr hole replacement and have superior biocompatibility compared to PLLA screws.
A recently commercialised hydroxyapatite electrochemically assisted chemical deposition technique (BoneMaster) has been shown to induce increased bone apposition; whether this response is caused by the surface topography or chemistry is unknown. An in-vitro examination using human osteoblast-like cells was performed on a series of BoneMaster-coated surfaces. The chemistry was separated from the topography using a thin gold coating; Thermanox coverslips were used as a control. BoneMaster surfaces showed significantly greater alkaline phosphatase activity and osteocalcin production compared with controls; however, no difference was found between the gold-coated and uncoated BoneMaster samples, indicating topography is the main contributing factor.
Numerous biomaterials based on extracellular matrix-components have been developed. It was our aim to investigate whether a hyaluronic acid–based hydrogel improves neuronal survival and tissue preservation in organotypic spinal cord slice cultures. Organotypic spinal cord slice cultures were cultured for 4 days in vitro (div), either on hyaluronic acid–based hydrogel (hyaluronic acid–gel group), collagen gel (collagen group), directly on polyethylene terephthalate membrane inserts (control group), or in the presence of soluble hyaluronic acid (soluble hyaluronic acid group). Cultures were immunohistochemically stained against neuronal antigen NeuN and analyzed by confocal laser scanning microscopy. Histochemistry for choline acetyltransferance, glial fibrillary acidic protein, and Griffonia simplicifolia isolectin B4 followed by quantitative analysis was performed to assess motorneurons and different glial populations. Confocal microscopic analysis showed a 4-fold increase in the number of NeuN-positive neurons in the hyaluronic acid–gel group compared to both collagen (p < 0.001) and control groups (p < 0.001). Compared to controls, organotypic spinal cord slice cultures maintained on hyaluronic acid–based hydrogel showed 5.9-fold increased survival of choline acetyltransferance-positive motorneurons (p = 0.008), 2-fold more numerous resting microglial cells in the white matter (p = 0.031), and a 61.4% reduction in the number of activated microglial cells within the grey matter (p = 0.05). Hyaluronic acid–based hydrogel had a shear modulus (G') of 1200 Pascals (Pa), which was considerably higher than the 25 Pa measured for collagen gel. Soluble hyaluronic acid failed to improve tissue preservation. In conclusion, hyaluronic acid–based hydrogel improves neuronal and – most notably – motorneuron survival in organotypic spinal cord slice cultures and microglial activation is limited. The positive effects of hyaluronic acid–based hydrogel may at least in part be due to its mechanical properties.
Purpose: Adequate filling of bone defects still poses a challenge in every day clinical work. As many bone defects are irregularly shaped the need for appropriate scaffolds reaching the complete defect surface are great. The purpose of this pre-clinical pilot study was to investigate the handling, biocompatibility, biodegradation and osteoconductivity of a new pasty bone substitute (pure phase β-TCP, hyaluronic acid, methylcellulose) in bone tissue.
Methods: In an unilateral tibial defect model the peri-implant and bone tissue response to the new pasty bone substitute was tested in New Zealand white rabbits for up to 24 weeks compared to empty controls. Analysis included HR-pQCT scans, histomorphometric evaluation and quantification of vascularization of un-decalcified histological slices.
Results: After 1 week the experimental group presented significantly higher new bone volume fraction (p = 0.021) primarily consisting of immature bone matrix and higher vessel density compared to controls (p = 0.013). After 4 weeks bone formation was not significantly different to controls but was distributed more evenly throughout the defect. Bone matrix was now mineralized and trabeculae were thicker than in controls (p = 0.002) indicating faster intramedullary bone maturation. Controls presented extensive periosteal bone formation, major fibrous tissue influx and high vascularization. After 12 and 24 weeks there was no new bone detectable. There were no severe signs of inflammation at all time points.
Conclusion: The substitute showed an early induction of bone formation. It promoted accelerated intramedullary bone repair and maturation and prevented periosteal bone formation indicating its potential use for reconstructive surgery of bone defects.
The aim of this study was to design a new natural/synthetic bioactive bone scaffold for potential use in bone replacement applications. We developed a tri-component osteogenic composite scaffold made of collagen (Coll), hydroxyapatite (HA) and poly(l-lactide-co--caprolactone) (PLCL). This Coll/HA/PLCL composite scaffold was combined with human osteoblast-like cells obtained by differentiation of dental pulp stem cells (DPSCs) to engineer bone tissue in vitro. Results show that the 3D Coll/HA/PLCL composite scaffold was highly porous, thereby enabling osteoblast-like cell adhesion and growth. Cultured in the Coll/HA/PLCL scaffold, the osteoblast-like cells expressed different osteogenic genes, produced alkaline phosphatase and formed nodules more than did PLCL alone. Micro-CT analyses revealed a significant (30%) increase of tissue mineralisation on the surface as well as inside of the Coll/HA/PLCL scaffold, thus confirming its effectiveness as a bone regeneration platform.
The major component of fibrous extracellular matrix of dermis is composed of a complex combination of proteins and polysaccharides. Electrospun cellulose acetate/gelatin might be an effective simulator of the structure and composition of native skin and during this study, we electrospun cellulose acetate/gelatin membranes in various compositions and their performance as a scaffold for either skin tissue engineering or as a wound dressing was evaluated. Skin treatment products, whether tissue-engineered scaffolds or wound dressings, should be sufficiently hydrophilic to allow for gas and fluid exchange and absorb excess exudates while controlling the fluid loss. However, a wound dressing should be easily removable without causing tissue damage and a tissue-engineered scaffold should be able to adhere to the wound, and support cell proliferation during skin regeneration. We showed that these distinct adherency features are feasible just by changing the composition of cellulose acetate and gelatin in composite cellulose acetate/gelatin scaffolds. High proliferation of human dermal fibroblasts on electrospun cellulose acetate/gelatin 25:75 confirmed the capability of cellulose acetate/gelatin 25:75 nanofibers as a tissue-engineered scaffold, while the electrospun cellulose acetate/gelatin 75:25 can be a potential low-adherent wound dressing.
The bone growth promoting effects of statins suggest that these bioactive molecules can be used to improve the integration of bone-anchored implants. This study aimed at the application of simvastatin with dental implants for use in patients with low bone density. Coin-shaped titanium zirconium samples with grit-blasted and acid-etched surface were coated with simvastatin, using a novel anodic oxidation setup under alkaline conditions. The presence of intact simvastatin attached to the surface was confirmed by infrared spectroscopy. A binding site on the aliphatic O-H group was discovered and the integration of 1H, 18O and 12C in the depth of the surface were observed by secondary ion mass spectroscopy. A simvastatin concentration of about 60 g/cm2 was found in a release study over 72 h. The simvastatin-coated surfaces promoted alkaline phosphatase, collagen type I and osteocalcin gene expression of MC3T3-E1 cells. This suggested that the demonstrated coating holds potential for use in patients with compromised bone.
Novel techniques for creating a strong bond between polymeric matrices and biometals are required. We immobilized polymeric matrices on the surface of biometal for drug-eluting stents through covalent bond. We performed to improve the bonding strength between a cobalt–chromium alloy and a citric acid-crosslinked gelatin matrix by ultraviolet irradiation on the surface of cobalt–chromium alloy. The ultraviolet irradiation effectively generated hydroxyl groups on the surface of the alloy. The bonding strength between the gelatin matrix and the alloy before ultraviolet irradiation was 0.38 ± 0.02 MPa, whereas it increased to 0.48 ± 0.02 MPa after ultraviolet irradiation. Surface analysis showed that the citric acid derivatives occurred on the surface of the cobalt–chromium alloy through ester bond. Therefore, ester bond formation between the citric acid derivatives active esters and the hydroxyl groups on the cobalt–chromium alloy contributed to the enhanced bonding strength. Ultraviolet irradiation and subsequent immobilization of a gelatin matrix using citric acid derivatives is thus an effective way to functionalize biometal surfaces.
Nanoscale patterning of scaffolds provides broad surface for adhesion and differentiation of stem cells. As we know, the combination of tissue engineering with stem cells technology hold the key for regeneration of damaged tissues for example skeletal muscle tissues. On the other hand, the mechanical assessments of poly -caprolacton nanofibers determined the required features of biomedical scaffold for skeletal muscle tissue. In this study, skeletal muscle satellite cells as the main group of stem cells were cultivated on the electrospun poly -caprolacton nanofibers. Our results indicated that in comparison with tissue culture polystyrene, the nanoscale of scaffolds provided more induction to matured cells of skeletal muscle. Moreover, the immobilization of cells by collagen on poly -caprolacton nanofibers significantly improved the differential potency of satellite cells.
Pulsed laser deposition was used to deposit bioactive triphasic glass-ceramic composition (HASi) over titanium substrate using dense HASi target. Bioactive glass compositions are considered the most useful synthetic materials for immediate bone attachment because of its bioresorption, osteoconduction and osteointegration characteristics under in vivo conditions. The disadvantage of its brittleness associated with bioactive glass-ceramics has prompted its coating over metallic implants for the combination of duo mechanical and bioactive properties. The hard HASi target was able to undergo laser ablation under ambient gas pressure without bulk erosion of the target. Laser deposition was found to be efficient in depositing triphasic composition for immediate bone integration. The target and deposits were analyzed for the phase, composition and microstructural characteristics by means of X-ray diffraction, Fourier transform infrared spectroscopy, energy-dispersive X-ray analysis and scanning electron microscopy. Simultaneously, the adherent nature and mechanical behaviour of deposits were confirmed by scratch test and micro-indentation methods. Further, the in vitro dissolution and bioactivity were assessed by soaking in simulated body fluid followed by elemental analysis using inductively coupled plasma spectroscopy. The deposits were found to be cell-friendly, which was indicated by the phenomenology of stem cells under in vitro conditions.
Traumatic injury is the leading cause of death in people aged 44 or less in the US. It is also estimated that 82% of deaths from battlefield hemorrhage may be survivable with better treatment options. In this study, two biomaterial hemostats having disparate mechanisms were evaluated in a large animal lethal hemorrhage model and compared to a commercial product and standard cotton gauze. We hypothesized that the biomaterial with a biologically active mechanism, as opposed to a mechanical mechanism, would be the most effective in this model. Using a published study protocol, the femoral artery in swine was punctured and treated. KeraStat™ (KeraNetics) and Nanosan®-Sorb (SNS Nano) hemostats were compared to a commercial chitosan dressing (second generation Hemcon®) and cotton gauze. Both KeraStat and Nanosan increased survival, significantly increased mean arterial pressure (MAP), and significantly decreased shock index compared to both controls. The Hemcon dressing was no different than gauze. Platelet adhesion assays suggested that the KeraStat mechanism of action involves β1 integrin mediated platelet adhesion while Nanosan-Sorb operates similar to one reported mechanism for Hemcon, absorbing fluid and concentrating clotting components. The Nanosan also swelled considerably and created pressure within the wound site even after direct pressure was removed.
The present article deals with the development of 3D porous scaffolds for bone grafting. They were prepared based on rapid fluid infiltration of Al2O3-SiO2 sol into a polyethylene non-woven fabric template structure. Titanium dioxide in concentration equal to 5 wt% was added to the Al2O3-SiO2 mixture to produce Al2O3-SiO2-TiO2 composite scaffolds. The prepared scaffolds are characterized by means of X-ray diffraction, scanning electron microscopy and three-point bending test techniques. The bioactivity of the produced bodies is discussed, including the in vitro and in vivo assessments. The produced scaffolds exhibit mean total porosity of 66.0% and three-point bending strength of 7.1 MPa. In vitro studies showed that MG-63 osteoblast-like cells attach and spread on the scaffolds surfaces. Furthermore, cells grew through the scaffolds and start to produce extra-cellular matrix. Additionally, in vivo studies revealed the ability of the porous scaffolds to regenerate bone tissue in femur defects of albino rats 5 months post surgery. Histological analysis showed that the defect is almost entirely filled with new bone. The formed bone is characterized as a mature bone. The produced bone grafts are intended to be used as bone substitute or bone filler as their degradation products caused no inflammatory effects.
In order to develop novel, effective therapies for central nervous system regeneration, it is essential to better understand the role of neurotrophic factors and to design, accordingly, better artificial scaffolds to support both neurite outgrowth and synapse formation. Both nerve growth factor and brain-derived neurotrophic factor are major factors in neural survival, development, synaptogenesis, and synaptic connectivity of primary cultured neurons. As a prime candidate coating material for such neural cultures, carbon nanotubes offer unique structural, mechanical, and electrical properties. In this study, carbon nanotubes coated glass-coverslips were used as the matrix of a primary neural culture system used to investigate the effects of carbon nanotubes on neurite outgrowth and nerve growth factor/brain-derived neurotrophic factor release and expression. For these purposes, we performed comparative analyses of primary cultured neurons on carbon nanotubes coated, non-coated, and Matrigel-coated coverslips. The morphological findings showed definite carbon nanotubes effects on the neurite outgrowths and synaptogenic figures in both cortical and hippocampal neurons when compared with the non-coated negative control. Although the carbon nanotubes did not change neurotrophin expression levels, it stimulated brain-derived neurotrophic factor release into the media from both types of neurons. Accordingly, we suggest a different mechanism of action between carbon nanotubes and Matrigel in relation to the specific neurotrophic factors. Since carbon nanotubes supply long-term extracellular molecular cues for the survival and neurite outgrowths of cultured neurons, the results from this study will contribute to an understanding of carbon nanotubes biological effects and provide new insight into their role in the secretion of neurotrophic factors.
Cellulose acetate phthalate and Pluronic F-127 combined together (70:30 wt:wt) create a rigid, surface-eroding association polymer. To impart flexibility into the polymer system and allow for a drug delivery film that can contour to varying wound shapes, plasticizers were added. Triethyl citrate or tributyl citrate was combined with cellulose acetate phthalate and Pluronic F-127 at 0, 10, or 20 wt%. Mechanical analysis was performed on the films as they were prepared and following a 2-h incubation in phosphate-buffered saline. Tensile tests showed that higher plasticizer content increased the % elongation but decreased the elastic modulus and ultimate tensile strength. The effect triethyl citrate had on the % elongation was twice as much than that of tributyl citrate. After incubation, % elongation, elastic modulus, and ultimate tensile strength all increased because plasticizer leached out of the films. Microcomputed tomography and scanning electron microscopy were performed on the samples both before and after incubation to determine how erosion and leaching of plasticizer affected the interior and exterior structure of the films. Porosity increased as plasticizer content increased; however, plasticizer content did not have a significant effect on the rate of erosion. The mechanical properties of cellulose acetate phthalate–Pluronic films can be adjusted by the type and amount of plasticizer added to the system and therefore can be tailored for different drug delivery applications.
The aim of this work is to assess the influence of two blast media on the deposition of hydroxyapatite onto a titanium substrate using a novel ambient temperature coating technique named CoBlast. CoBlast was developed to address the problems with high temperature coating techniques. The blasting media used in this study were Al2O3 and a sintered apatite powder. The prepared and coated surfaces were compared to plasma sprayed hydroxyapatite on the same substrates using the same hydroxyapatite feedstock powder. X-ray diffraction analysis revealed the coating crystallinity was the same as the original hydroxyapatite feedstock powder for the CoBlast samples while evidence of amorphous hydroxyapatite phases and β-TCP was observed in the plasma sprayed samples. The blast media type significantly influences the adhesive strength of the coating, surface roughness of both the substrate and coating and the microstructure of the substrate. The coating adhesion increased for the CoBlasted samples from 50 MPa to 60 MPa for sintered apatite powder and alumina, respectively, while plasma spray samples were significantly lower (5 MPa) when tested using a modified pull-test. In conclusion, the choice of blast medium is shown to be a key parameter in the CoBlast process. This study indicates that sintered apatite powder is the most suitable candidate for use as a blast medium in the coating of medical devices.
In this work, we fabricated injectable bone substitutes modified with the addition of bioactive glass powders synthesized via ultrasonic energy-assisted hydrothermal method to the calcium phosphate-based bone cement to improve its biocompatibility. The injectable bone substitutes was initially composed of a powder component (tetracalcium phosphate, dicalcium phosphate dihydrate and calcium sulfate dehydrate) and a liquid component (citric acid, chitosan and hydroxyl-propyl-methyl-cellulose) upon which various concentrations of bioactive glass were added: 0%, 10%, 20% and 30%. Setting time and compressive strength of the injectable bone substitutes were evaluated and observed to improve with the increase of bioactive glass content. Surface morphologies were observed via scanning electron microscope before and after submersion of the samples to simulated body fluid and increase in apatite formation was detected using x-ray diffraction machine. In vitro biocompatibility of the injectable bone substitutes was observed to improve with the addition of bioactive glass as the proliferation/adhesion behavior of cells on the material increased. Human gene markers were successfully expressed using real time-polymerase chain reaction and the samples were found to promote cell viability and be more biocompatible as the concentration of bioactive glass increases. In vivo biocompatibility of the samples containing 0% and 30% bioactive glass were evaluated using Micro-CT and histological staining after 3 months of implantation in male rabbits’ femurs. No inflammatory reaction was observed and significant bone formation was promoted by the addition of bioactive glass to the injectable bone substitute system.
The setup of colloidal hybrid nanosystems based on biomimetic calcium phosphate apatites doped with europium ions has recently raised great interest in the pharmacological community, especially due to their bio-inspired character. This is especially relevant in relation with medical imaging for cancer diagnosis. Questions however remain in relation to a number of applicability aspects, some of which have been examined in this contribution. In a first part of this work, we explored further the luminescence properties of such colloidal nanoparticles. We pointed out, upon excitation of europium, the existence of some non-radiative de-excitation via the vibration of O-H oscillators located at the vicinity of the Eu3+ luminescent centers. The replacement of Eu3+ by Tb3+ ions, less prone to non-radiative de-excitation, was then tested in a preliminary way and can be seen as a promising alternative. In a second part of this work, we inspected the possibility to store these colloids in a dry state while retaining a re-suspension ability preserving the nanometer size of the initial nanoparticles, and we propose a functional protocol involving the addition of glucose prior to freeze-drying. We finally showed for the first time, based on titrations of intracellular Ca2+ and Eu3+ ions, that folic acid-functionalized biomimetic apatite nanoparticles were able to target cancer cells that overexpress folate receptors on their membrane, which we point out here in the case of T-47-D breast carcinoma cells, as opposed to ZR-75-1 cells that do not express folate receptors. This contribution thus opens new exciting perspectives in the field of targeted cancer diagnosis, thus confirming the promise of biomimetic apatites-based colloidal formulations.
Single nanofibers with chemical and functional properties consistent with artery extracellular matrix nanofibers were produced by electrospinning. Using weight ratios to mimic artery extracellular matrix, five materials were tested: (1) Collagen type I, (2) Collagen type I + Collagen type III, (3) Collagen type I + poly (diol citrate), (4) Collagen type I + Collagen type III + poly (diol citrate), and (5) Collagen type I + poly (diol citrate) + Decorin + Aggrecan. Fiber sizes for all materials ranged from 50 nm to 600 nm and random fiber mats had pore sizes from 21 to 40 = m2 and porosities of 72–84%. Human embryonic palatal mesenchymal cells fibroblasts adhered to all fibers and proliferated over a 7-day study period. Mechanical properties of single fibers were investigated using a combined atomic force/optical microscope. Materials containing poly (diol citrate) showed elasticity increased 3.2 fold greater than composites without poly (diol citrate). Maximum stress was within functional range in comparison to decellularized artery extracellular matrix fibers. By incorporating poly (diol citrate) and proteoglycan along with collagen, a viscoelastic nanofibrous material was produced for use in tissues such as artery where viscoelasticity and tensile strength are required.
Biomaterials-associated thrombosis is dependent critically upon electrochemical response of fibrinogen on material surface. The relationship between the response and anti-thrombogenicity of biomaterials is not well-established. Titanium oxide appears to have good anti-thrombogenicity and little is known about its underlying essential chemistry. We correlate their anti-thrombogenicity directly to electrochemical behaviors in fibrinogen containing buffer solution. High degree of inherent n-type doping was noted to contribute the impedance preventing charge transfer from fibrinogen into film (namely its activation) and consequently reduced degree of anti-thrombogenicity. The impedance was the result of high donor carrier density as well as negative flat band potential.
To verify the compatibility of rigid supports with neuronal cells for biomechanical application, we have evaluated the biocompatibility of Zn-doped bioglasses versus neuronal cell line SKNBE. Undifferentiated and retinoic acid-differentiated cells were used. We have observed that bioglasses doped with low concentration of Zn favored cell adhesion and proliferation of undifferentiated SKNBE neuronal cells, while the high Zn concentration strongly interfered with cell proliferation. Instead the high Zn concentration lightly stimulates the adhesive and strongly stimulates the phenotype characterization of differentiated SKNBE cells. Focal contact sites were observed in cells performing spread adhesive morphology, while they were down-regulated in cells performing differentiation behavior. GAP-43 and neurofilament were expressed in differentiated cells. However, GAP-43 was also found to be expressed in undifferentiated cells, where its expression seems related to proliferative behavior of cells. This work evidenced the importance of the biomaterial chemical structure in influencing proliferation or differentiation pathways of neuronal cells.
In this study, we investigated the effects of human primary chondrocytes, derived from routine septorhino- and otoplasties on a novel nondegradable biomaterial. This biomaterial, porous bacterial nanocellulose, is produced by Gluconacetobacter xylinus. Porosity is generated by paraffin beads embedded during the fermentation process. Human primary chondrocytes were able to adhere to bacterial nanocellulose and produce cartilaginous matrix proteins such as aggrecan (after 14 days) and collagen type II (after 21 days) in the presence of differentiation medium. Cells were located within the pores and in a dense cell layer covering the surface of the biomaterial. Cells were able to re-differentiate, as cell shape and extra cellular matrix gene expression showed a chondrogenic phenotype in three-dimensional bacterial nanocellulose culture. Collagen type I and versican expression decreased during three-dimensional culture. Variations in pore sizes of 150–300 µm and 300–500 µm did not influence cartilaginous extra cellular matrix synthesis. Varying seeding densities from 9.95 x 102 to 1.99 x 103 cells/mm2 and 3.98 x 103 cells/mm2 did not result in differences in quality of extra cellular matrix neo-synthesis. Our results demonstrated that both nasal and auricular chondrocytes are equally suitable to synthesize new extra cellular matrix on bacterial nanocellulose. Therefore, we propose both cell sources in combination with bacterial nanocellulose as promising candidates for the special needs of auricular reconstruction.
The aim of this pilot study was to evaluate the bioactive, surface-coated polycaprolactone-co-lactide scaffolds as bone implants in a tibia critical size defect model. Polycaprolactone-co-lactide scaffolds were coated with collagen type I and chondroitin sulfate and 30 piled up polycaprolactone-co-lactide scaffolds were implanted into a 3 cm sheep tibia critical size defect for 3 or 12 months (n = 5 each). Bone healing was estimated by quantification of bone volume in the defects on computer tomography and microcomputer tomography scans, plain radiographs, biomechanical testing as well as by histological evaluations. New bone formation occurred at the proximal and distal ends of the tibia in both groups. The current pilot study revealed a mean new bone formation of 63% and 172% after 3 and 12 months, respectively. The bioactive, surface coated, highly porous three-dimensional polycaprolactone-co-lactide scaffold stack itself acted as a guide rail for new bone formation along and into the implant. These preliminary data are encouraging for future experiments with a larger group of animals.
Currently, patient’s own growth factors from platelet-rich plasma and platelet-rich fibrin have been clinically used for repair and regeneration of defective tissues. In platelet-rich plasma and platelet-rich fibrin, fibrin gel is formed from blood fibrinogen and functions as a carrier for growth factors. In this study, the growth factors were extracted from the platelet-rich fibrin and incorporated into a gelatin gel by mixing the platelet-rich fibrin extract and gelatin solution before cross-linking with glutaraldehyde. About 70% of TGF-β1 was found to be released in vitro from the gelatin gel containing the platelet-rich fibrin extract into phosphate-buffered saline (–) in 7 days. The gelatin gel containing basic fibroblast growth factor, prepared as a comparison, showed a similar release profile. The gelatin gels were slowly degraded with time after subcutaneous implantation on the back of rats, and the gel containing the platelet-rich fibrin extract strongly induced neovascularization and granulation tissue formation around the implantation site compared to the gel only and the gel containing basic fibroblast growth factor, platelet-rich plasma, or platelet-rich fibrin. The gelatin gel containing the platelet-rich fibrin extract was attempted as wound dressing on a full-thickness skin defect model. After 2 weeks of application, the gel was found to be more effective in acceleration of wound healing than the commonly used platelet-rich plasma.
Magnesium alloys have been investigated in different fields of medicine and represent a promising biomaterial for implants due to characteristics like bioabsorbability and osteoinduction. The objective of this study was to evaluate the usability of magnesium as implant material in middle ear surgery. Magnesium implants were placed into the right middle ear of eighteen New Zealand White rabbits. Nine animals were euthanized after four weeks and nine animals after three month. The petrous bones were removed and embedded in epoxy resin. The specimens were then polished, stained and evaluated with the aid of a light microscope. The histological examination revealed a good biocompatibility. After four weeks, a beginning corrosion of the implant’s surface and low amount of trabecular bone formation in the area of the stapes base plate was observed. A considerable degradation of implants and obvious bone formation was found three month after implantation. The magnesium alloy used in the present study partly corroded too fast, so that a complete bone reconstruction could not be established in time. The increased osteoinduction on the stapes base plate resulted in a tight bone-implant bonding. Thus, a promising application of magnesium could be a coating of biomaterials in order to improve the bony integration of implants.
Biodegradable magnesium-based implants are currently being developed for use in orthopedic applications. The aim of this study was to investigate the acute, subacute, and chronic local effects on bone tissue as well as the systemic reactions to a magnesium-based (MgYREZr-alloy) screw containing rare earth elements. The upper part of the screw was implanted into the marrow cavity of the left femora of 15 adult rabbits (New Zealand White), and animals were euthanized 1 week, 12 weeks, and 52 weeks postoperatively. Blood samples were analyzed at set times, and radiographic examinations were performed to evaluate gas formation. There were no significant increased changes in blood values compared to normal levels. Histological examination revealed moderate bone formation with direct implant contact without a fibrous capsule. Histopathological evaluation of lung, liver, intestine, kidneys, pancreas, and spleen tissue samples showed no abnormalities. In summary, our data indicate that these magnesium-based screws containing rare earth elements have good biocompatibility and osteoconductivity without acute, subacute, or chronic toxicity.
The development of a small diameter (≤5 mm) arterial prosthesis requires the appropriate selection of materials, structure and fabrication method so as to provide adequate mechanical properties, superior biocompatibility and precise control over the diameter. In this study, 100% polyester, 100% silk fibroin and a combination of both yarns were woven into seamless tubular prototype prostheses with different basic weaves. After degumming/scouring they met a target inner diameter of 3.9±0.3 mm which demonstrates that weaving is a precise way to manufacture small caliber arterial prostheses. In conclusion, the bicomponent polyester/silk woven samples had superior mechanical properties and improved cytocompatibility compared to commercial ePTFE devices.
Borate bioactive glass has been shown to convert faster and more completely to hydroxyapatite and enhance new bone formation in vivo when compared to silicate bioactive glass (such as 45S5 and 13-93 bioactive glass). In this work, the effects of the borate glass microstructure on its conversion to hydroxyapatite (HA) in vitro and its ability to support tissue ingrowth in a rat subcutaneous implantation model were investigated. Bioactive borate glass scaffolds, designated 13-93B3, with a grid-like microstructure and pore widths of 300, 600, and 900 µm were prepared by a robocasting technique. The scaffolds were implanted subcutaneously for 4 weeks in Sprague Dawley rats. Silicate 13-93 glass scaffolds with the same microstructure were used as the control. The conversion of the scaffolds to HA was studied as a function of immersion time in a simulated body fluid. Histology and scanning electron microscopy were used to evaluate conversion of the bioactive glass implants to hydroxyapatite, as well as tissue ingrowth and blood vessel formation in the implants. The pore size of the scaffolds was found to have little effect on tissue infiltration and angiogenesis after the 4-week implantation.
Hydroxyapatite was deposited on pure magnesium (Mg) with a flexible poly(-caprolactone) interlayer to reduce the corrosion rate of Mg and enhance coating flexibility. The poly(-caprolactone) interlayer was uniformly coated on Mg by a spraying method, followed by hydroxyapatite deposition on the poly(-caprolactone) using an aerosol deposition method. In scanning electron microscopy observations, inorganic/organic composite-like structure was observed between the hydroxyapatite and poly(-caprolactone) layers, resulting from the collisions of hydroxyapatite particles into the poly(-caprolactone) matrix at the initial stage of the aerosol deposition. The corrosion resistance of the coated Mg was examined using potentiodynamic polarization tests. The hydroxyapatite/poly(-caprolactone) double coating remarkably improved the corrosion resistance of Mg in Hank’s solution. In the in vitro cell tests, the coated Mg showed better cell adhesion compared with the bare Mg due to the reduced corrosion rate and enhanced biocompatibility. The stability and flexibility of hydroxyapatite/poly(-caprolactone) double coating was investigated by scanning electron microscopy inspections after the coated Mg was deformed. The hydroxyapatite coating on the poly(-caprolactone) interlayer revealed enhanced coating stability and flexibility without cracking or delamination during bending and stretching compared with the hydroxyapatite single coating. These results demonstrated that the hydroxyapatite/poly(-caprolactone) double coating significantly improved the surface corrosion resistance of Mg and enhanced coating flexibility for use of Mg as a biodegradable implant.
Polymeric substrates with good biocompatibility have been widely employed to create a living construct with the complexities of tissue histology and function in the field of tissue engineering. In this study, poly(ester-urethane) (58213, NAT022) was used to be substrate due to its good physical and chemical properties. Proteins like gelatin or silk fibroin were covalently bonded on its surface using method of diamine aminolysis and glutaraldehyde crosslinking, which had been setup in our group in order to improve poly(ester-urethane)’s hydrophilicity and biocompatibility. The modification was proved by the measurements of static and dynamic contact angles and fluorescence detection. The biological properties were evaluated as in vitro cell culture and in vivo transplantation via cell number counting, morphology observation, immunohistochemistry analysis, etc. The results showed that gelatin or silk fibroin grafted membrane displayed good cytocompatibility, i.e. good proliferation and differentiation of human hypopharynx fibroblast and skeletal muscle cell though the control poly(ester-urethane) indicated low toxicity to cells and good biocompatibility, which was also verified in in vivo experiment. After poly(ester-urethane)–silk fibroin was implanted subcutaneously in rat back, it exhibited a better compatibility to peripheral tissue and faster biodegradation than the control poly(ester-urethane) did. This information supplied us valuable knowledge for poly(ester-urethane) to be used as matrix in situ hypopharynx regeneration study.
The purpose of this study was to analyze the encapsulation of superparamagnetic iron oxide nanoparticles (SPION) by the lipid nanoparticle conjugated with the 12-mer peptides (RLLDTNRPLLPY, L-peptide), and the delivery of this complex into living cells. The lipid nanoparticles employed in this work were highly hydrophilic, stable, and contained poly(ethylene-glycol) for conjugation to the bioactive L-peptide. The particle sizes of two different magnetic lipid nanoparticles, L-peptide modified (LML) and non-L-peptide modified (ML), were both around 170 nm with a narrow range of size disparity. The transversal relaxivity, r2, for both LML and ML nanoparticles were found to be significantly higher than the longitudinal relaxivity r1 (r2/r1 > 20). The in vitro tumor cell targeting efficacy of the LML nanoparticles were evaluated and compared to the ML nanoparticles, upon observing cellular uptake of magnetic lipid nanoparticles by the nasopharyngeal carcinoma cells, which express cell surface specific protein for the L-peptide binding revealed. In the Prussian blue staining experiment, cells incubated with LML nanoparticles indicated much higher intracellular iron density than cells incubated with only the ML and SPION nanoparticles. In addition, the MTT assay showed the negligible cell cytotoxicity for LML, ML and SPION nanoparticles. The MR imaging studies demonstrate the better T2-weighted images for the LML-nanoparticle-loaded nasopharyngeal carcinoma cells than the ML- and SPION-loaded cells.
Rationale: Prosthetic heart valves designed to be implanted percutaneously must be loaded within delivery catheters whose diameter can be as low as 18 F (6 mm). This mandatory crimping of the devices may result in deleterious damages to the tissues used for valve manufacturing. As bovine and porcine pericardial tissue are currently given preference because of their excellent availability and traceability, a preliminary comparative study was undertaken to highlight their potential advantages.
Materials and methods: Bovine and pericardium patches were compared morphologically (light microscopy, scanning electron microscopy and transmission electron microscopy). The acute thrombogenicity of both materials was measured in term of platelet uptake and observed by scanning electron microscopy, porcine intact and injured arteries being used as controls. The pericardium specimens were also subjected to uniaxial tensile tests to compare their respective mechanical characteristics.
Results: Both pericardiums showed a layered architecture of collagen bundles presenting some interstitial cells. They displayed wavy crimps typical of an unloaded collagenous tissue. The collagen bundles were not bound together and the fibrils were parallel with characteristic periodicity patterns of cross striations. The mesothelial cells found in vivo on the serous surface were no longer present due to tissue processing, but the adjacent structure was far more compacted when compared to the fibrous side. The fibrinocollagenous surfaces were found to be more thrombogenic for both bovine and porcine tissues and the serous side of the porcine pericardium retained more platelets when compared to the bovine samples, making the acute thrombogenicity more important in the porcine pericardium.
Conclusion: Both bovine and porcine pericardium used in cardiovascular implantology can be selected to manufacture percutaneous heart valves. The selection of one pericardium preferably to the other should deserve additional testing regarding the innocuousness of crimping when loaded in delivery catheters and the long-term durability after percutaneous deployment.
Due to limitations of bone autografts and allografts, synthetic bone grafts using osteoconductive biomaterials have been designed. In this study, collagen–chitosan–calcium phosphate microparticle-based scaffolds fused with glycolic acid were compared to their counterparts without collagen in terms of degradation, cytocompatibility, porosity, and Young’s modulus. It was found that 26–30% collagen was incorporated and that hydroxyapatite was present. Moreover, there were no differences between control and collagen scaffolds in degradation, cytocompatibility, porosity, and Young’s modulus. In general, scaffolds exhibited 23% porosity, 0.6–1.2 MPa Young’s modulus, 23% degradation over 4 weeks, and supported a four to seven fold increase in osteoblast cell number over 7 days in culture. Collagen can be incorporated into these bone graft substitute scaffolds, which show an improved degradation profile.
In this study, porous poly(-caprolactone) (PCL) fiber-based fibrous scaffolds are created using a suitable ratio of dimethyl chloride and acetone by using electrospinning. With the porous structure, it induced CaP particles to easily coat on the fibers after immersion in simulated body fluid solution. The morphology of the electrospun membranes was observed using scanning electron microscopic observation. The results showed that the CaP coated successfully, as examined by scanning electron microscopy, energy-dispersive spectroscopy, X-ray diffraction, transmission electron microscopic techniques and mass comparative analysis. The wettability of the coated fibrous scaffolds was tested using contact angle analysis. The in vitro cellular proliferation and cell interaction with fibrous scaffolds were investigated. In addition, the in vivo bone formation capacity of fibrous scaffolds including the non-porous (PCL-DCM), porous (PCL-DCM/Ace) and CaP coating on PCL/DCM-Ace for 2, 4, 8 and 12 h immersed in SBF solution were also investigated. By measuring the in vitro results, we verified that porous PCL fiber-based fibrous scaffold after 12 h of immersion in simulated body fluid (PCL-DCM/Ace-12) was excellent for cell interaction, growth and proliferation. The in vivo analyses showed that the PCL-DCM/Ace-12 fibrous scaffold enabled greater acceleration of bone formation than PCL/DCM and PCL/DCM-Ace fibrous scaffolds.
There is an increasing need for synthetic bone substitute materials that decrease the need for allografts and autografts. In this study, composites of β-tricalcium phosphate and a biodegradable poly(L-lactide-co--caprolactone) were manufactured using extrusion to form biodegradable composites with high β-tricalcium phosphate contents for osteoconductivity. The hydrolytic degradation of the composites containing 0, 10, 20, 35 and 50% of β-tricalcium phosphate was studied in vitro for 52 weeks. During the study, it was observed that β-tricalcium phosphate did not have an effect on the degradation rate of the polymer matrix. However, the crystallinity of the materials increased throughout the test series and changes in glass transition temperatures were also observed as the comonomer ratio of the polymer matrix changed as the degradation proceeded. The results show that the materials have desirable degradation properties and, thus, possess great potential as bioabsorbable and osteoconductive bone filling materials.
We developed a continuously porous scaffold with laminated matrix and bone-like microstructure by a multi-pass extrusion process. In this scaffold, tetragonal ZrO2, biphasic calcium phosphate and poly-caprolactone layers were arranged in a co-axially laminated unit cell with a channel in the center. The entire matrix phase had a laminated microstructure of alternate lamina of tetragonal ZrO2, biphasic calcium phosphate and poly-caprolactone—biphasic calcium phosphate with optimized designed thickness and channeled porosity. Each of the continuous pores was coaxially encircled by the poly-caprolactone—biphasic calcium phosphate layer, biphasic calcium phosphate layer and finally tetragonal ZrO2 layer, one after the other. Before extrusion, 5 vol% graphite powder was mixed with tetragonal ZrO2 to ensure pores in the outer layer and connectivity among the lamellas. The design strategy is aimed to incorporate a lamellar microstructure like the natural bone in the macro-scaled ceramic body to investigate the strengthening phenomenon and pave the way for fabricating complex microstructure of natural bone could be applied for whole bone replacement. The final fabricated scaffold had a compressive strength of 12.7 MPa and porosity of 78 vol% with excellent cell viability, cell attachment and osteocalcin and collagen expression from cultured MG63 cells on scaffold.
Four different dynamic biomaterial surfaces with different molecular architectures were prepared using two hydrophilic polymers: poly(ethylene glycol) and polyrotaxanes containing α-cyclodextrin. Either one or both terminals of the poly(ethylene glycol) or polyrotaxanes were immobilized onto a gold substrate via Au-S bonds, resulting in poly(ethylene glycol)-graft, polyrotaxanes-graft, poly(ethylene glycol)-loop, and polyrotaxanes-loop structures. Human platelet adhesion was suppressed more effectively on the graft surfaces than on the loop surfaces for both poly(ethylene glycol) and polyrotaxanes due to the high mobility of graft polymer chains with a free terminal. Moreover, the platelets adhered to the polyrotaxane surfaces much less than the poly(ethylene glycol) surfaces, possibly because of the mobile nature of the α-cyclodextrin molecules that were threaded on the poly(ethylene glycol) chain. Actin filament assembly in adherent platelets was also greatly prevented on the poly(ethylene glycol)/polyrotaxanes-graft surfaces in comparison with the corresponding loop surfaces. A clear correlation between the numbers and areas of adherent platelets on these surfaces suggests that platelet adhesion and activation were dominated by the platelet GPIIb/IIIa-adsorbed fibrinogen interaction. These results indicate that both of the different modes of dynamic features, sliding/rotation of α-cyclodextrin and polymer chain mobility, effectively suppressed platelet adhesion in spite of the similar hydrophilicity. This research affords a novel chemical strategy for designing hemocompatibile biomaterial surfaces.
Magnetic resonance imaging is one of the most important fields for cellular imaging due to its non-invasive capacity, spatial resolution, and sensibility to visualized transplanted cells. An enhanced magnetic resonance image can be achieved by using contrast agents containing paramagnetic gadolinium chelates, which have the widest clinical use. To obtain a better contrast-enhancement and reduce the concentration of Gd for payload, one strategy is to conjugate the gadolinium(III) chelate to polymeric materials that will lead into an increase in the rotational correlation time and therefore improve the relaxivity. Four series of dextran gadolinium chelates were synthesized which are of interest as potential MRI contrast agents to track bone marrow-derived endothelial progenitor cells in vivo. The dextranes with molecular weights were characterized, introduced into the endothelial progenitor cells by electroporation, and injected in aqueous solution into rats to acquire the MR images. We have shown that by selecting polymers of the appropriate molecular weight, stability into the cell after labeling, relaxivity, and retention into the body can be accomplished.
An effective tumor-targeted drug delivery system for photodynamic therapy was developed by designing ligand-mediated nanoparticles with stable formulations of a hydrophobic photosensitizer. Novel folic acid (FA)-conjugated amphiphilic block copolymers of polyethylene glycol (PEG) and poly-β-benzyl-L-aspartate (PBLA) with the potential to act as pH-responsive drug release reservoirs were synthesized. The photosensitizer, 2,4-diacetyl deuteroporphyrin IX dimethyl ether (DD-PpIX), was conjugated to the copolymers through pH-sensitive hydrazone linkage. The syntheses and compositions of all copolymers were confirmed by 1H NMR measurement. Photosensitizer-conjugated amphiphilic copolymeric nanoparticles (FA-PEG-P(Asp-Hyd)-DD-PpIX) were prepared by micelle formation in aqueous solution. The particle sizes of the FA-PEG-PBLA and FA-PEG-P(Asp-Hyd)-DD-PpIX nanoparticles were determined by light-scattering measurements. The range was 105–298 nm, depending on copolymer molecular weight and composition. Field emission scanning electron microscopy showed that the FA-PEG-P(Asp-Hyd)-DD-PpIX copolymeric nanoparticles were submicron in size and spherical in shape. The results of in vitro release tests showed that the release profiles of DD-PpIX from the nanoparticles were strongly pH-dependent and influenced by the amount of photosensitizer that was conjugated. In vitro tests using HeLa cells indicated that the FA-PEG-P(Asp-Hyd)-DD-PpIX nanoparticles had low dark-toxicity and showed more than 97% of cellular uptake. Based on our results, the FA-PEG-P(Asp-Hyd)-DD-PpIX nanoparticle system could be a promising approach for developing novel photosensitizer delivery carriers for photodynamic therapy.
A range of crystalline and nano-sized carbonate- and silicate-substituted hydroxyapatite has been successfully produced by using continuous hydrothermal flow synthesis technology. Ion-substituted calcium phosphates are better candidates for bone replacement applications (due to improved bioactivity) as compared to phase-pure hydroxyapatite. Urea was used as a carbonate source for synthesising phase pure carbonated hydroxyapatite (CO3-HA) with 5 wt% substituted carbonate content (sample 7.5CO3-HA) and it was found that a further increase in urea concentration in solution resulted in biphasic mixtures of carbonate-substituted hydroxyapatite and calcium carbonate. Transmission electron microscopy images revealed that the particle size of hydroxyapatite decreased with increasing urea concentration. Energy-dispersive X-ray spectroscopy result revealed a calcium deficient apatite with Ca:P molar ratio of 1.45 (±0.04) in sample 7.5CO3-HA. For silicate-substituted hydroxyapatite (SiO4-HA) silicon acetate was used as a silicate ion source. It was observed that a substitution threshold of ~1.1 wt% exists for synthesis of SiO4-HA in the continuous hydrothermal flow synthesis system, which could be due to the decreasing yields with progressive increase in silicon acetate concentration. All the as-precipitated powders (without any additional heat treatments) were analysed using techniques including Transmission electron microscopy, X-ray powder diffraction, Differential scanning calorimetry, Thermogravimetric analysis, Raman spectroscopy and Fourier transform infrared spectroscopy.
Materials filled with a silicate glass (MSi) and a borate glass (MB) were developed and compared in terms of their in vitro behavior. The effect of filler composition and concentration (0, 30, 40 and 50 wt%) on the curing parameters, residual monomer, water uptake, weight loss, bioactivity, mechanical properties (bending and compression) and osteoblast cytocompatibility was evaluated. The addition of bioactive glass filler significantly improved the cements curing parameters and the mechanical properties. The most relevant results were obtained for the lower filler concentration (30 wt%) a maximum flexural strength of 40.4 MPa for MB3 and a maximum compressive strength of 95.7 MPa for MSi3. In vitro bioactivity in acellular media was enhanced by the higher glass contents in the cements. Regarding the biological assessment, the incorporation of the silicate glass significantly improved osteoblast cytocompatibility, whereas the presence of the borate glass resulted in a poor cell response. Nevertheless it was shown that the surviving cells on the MB surface were in a more differentiated stage compared to those growing over non-filled poly(methyl methacrylate). Results suggest that the developed formulations offer a high range of properties that might be interesting for their use as self-curing cements.
Embolization with micron-sized particulates is widely applied to treat uterine fibroids. The objective of this work was to develop mixture designs to predict materials composition–structure–property relationships for the SiO2–CaO–ZnO–La2O3–TiO2–MgO–SrO–Na2O glass system and compare its fundamental materials properties (density and cytocompatibility), against a state-of-the-art embolic agent (contour polyvinyl alcohol) to assess the potential of these materials for embolization therapies. The glass structures were evaluated using 29Si MAS NMR to identify chemical shift and line width; the particulate densities were determined using helium pycnometry and the cell viabilities were assessed via MTT assay. 29Si MAS NMR results indicated peak maxima for each glass in the range of -82.3 ppm to -89.9 ppm; associated with Q2 to Q3 units in silicate glasses. All experimental embolic compositions showed enhanced in vitro compatibility in comparison to Contour PVA with the exceptions of ORP9 and ORP11 (containing no TiO2). In this study, optimal compositions for cell viability were obtained for the following compositional ranges: 0.095–0.188 mole fraction ZnO; 0.068–0.159 mole fraction La2O3; 0.545–0.562 mole fraction SiO2 and 0.042–0.050 mole fraction TiO2. To ensure ease of producibility in obtaining good melts, a maximum loading of 0.068 mole fraction La2O3 is required. This is confirmed by the desirability approach, for which the only experimental composition (ORP5) of the materials evaluated was presented as an optimum composition; combining high cell viability with ease of production (0.188 mole fraction ZnO; 0.068 mole fraction La2O3; 0.562 mole fraction SiO2 and 0.042 mole fraction TiO2).
Protein polymer-based hydrogels have shown potential for tissue engineering applications, but require biocompatibility testing for in vivo use. Enzymatically crosslinked protein polymer-based hydrogels were tested in vitro and in vivo to evaluate their biocompatibility. Endotoxins present in the hydrogel were removed by Trition X-114 phase separation. The reduction of endotoxins decreased TNF-α production by a macrophage cell line in vitro; however, significant inflammatory response was still present compared to collagen control gels. A branched PEG molecule and dexamethasone were added to the hydrogel to reduce the response. In vitro testing showed a decrease in the TNF-α levels with the addition of dexamethasone. In vivo implantations into the epididymal fat pad of C57/BL6 mice, however, indicated a decreased inflammatory mediated immune response with a hydrogel treated with both PEGylation and endotoxin reduction. This study demonstrates the importance of endotoxin testing and removal in determining the biocompatibility of biomaterials.
The failure to understand the mechanisms of biomaterial-associated thrombosis prevents us from improving the blood compatibility of stents and mechanical heart valves. Blood-material interactions trigger a complex series of events and anticoagulant and anti-platelet therapies are needed to reduce the risks of thrombotic complications with most cardiovascular materials. While material interaction with platelets has been widely studied, little is currently known on material-induced leukocyte activation in the presence of shear. In vitro experiments were performed to assess the effect of flow on blood cell activation induced by medical grade metals, ST316L and TiAl6V4. Blood was circulated in flow chambers preloaded with or without metal wires at shear rates of 100, 500, and 1500 s-1. Platelet and leukocyte activation, leukocyte-platelet aggregation, and tissue factor expression on monocytes were measured by flow cytometry. Metal surfaces were characterized by scanning electron microscopy. Under physiological shear rates, no significant platelet microparticle formation was observed. However, significant CD11b up-regulation, leukocyte-platelet aggregates, and tissue factor expression were observed at 100 s-1. As shear rate increased to 1500 s-1, leukocyte activation reduced to control values. TiAl6V4-induced leukocyte activation was generally lower than that of ST316L. Adhesion significantly decreased with increasing shear rate to 1500 s-1.
In blood, increase within physiological shear rates led to a significant reduction in in vitro material-induced leukocyte activation, suggesting that difference between material biocompatibility may be better identified at low shear rates or under pathological shear conditions.
Gadolinium-based nanoparticles are novel objects with interesting physical properties, allowing their use for diagnostic and therapeutic applications. Gadolinium-based nanoparticles were imaged following intravenous injection in healthy rats and rats grafted with 9L gliosarcoma tumors using magnetic resonance imaging and scintigraphic imaging. Quantitative biodistribution using gamma-counting of each sampled organ confirmed that these nanoparticles were rapidly cleared essentially by renal excretion. Accumulation of these nanoparticles in 9L gliosarcoma tumors implanted in the rat brain was quantitated. This passive and long-duration accumulation of gadolinium-based nanoparticles in tumor, which is related to disruption of the blood–brain barrier, is in good agreement with the use of these nanoparticles as radiosensitizers for brain tumors.
Magnesium alloys are potential biodegradable materials for biomedical application. But their poor corrosion resistance may result in premature failure of implants. In this study, to solve this problem, Ca-P coatings were prepared on ZK60 magnesium alloy by a simple chemical conversion process and heat treatment. Surface characterization showed that a flake-like Dicalcium phosphate dihydrate (DCPD) (CaHPO4·2H2O) coating was formed on ZK60 alloy by the chemical conversion process. DCPD transformed into Dicalcium phosphate anhydrous (DCPa) (CaHPO4) and Ca2P2O7 after heat treatment. Results of potentiodynamic polarization showed the corrosion potential of ZK60 was increased from -1666 mV to -1566 mV with DCPD coating, while -1515 mV was obtained after heat treatment. The corrosion current density of ZK60 was measured to be reduced from 35 µA/cm2 to 3.5 µA/cm2 with DCPD coating, while a further reduction to 1 µA/cm2 was observed after heat treatment. This indicated that the coatings improved the substrate corrosion resistance significantly, and apparently, the heat-treated coating had a higher corrosion resistance. Immersion test demonstrated that both the coatings could provide protection for the substrate and the heat-treated coating could induce deposition of bone-like apatite. Cytotoxicity evaluation revealed that none of the samples induced toxicity to L-929 cells after 1- and 3-day culture. The cytocompatibility of ZK60 was improved by the coatings, with the following sequence: uncoated ZK60 < DCPD-coated ZK60 < heat-treated coating.
Eight different chemicals were investigated as potential candidate coupling agents for phosphate glass fibre reinforced polylactic acid composites. Evidence of reaction of the coupling agents with phosphate glass and their effect on surface wettability and glass degradation were studied along with their principle role of improving the interface between glass reinforcement and polymer matrix. It was found that, with an optimal amount of coupling agent on the surface of the glass/polymer, interfacial shear strength improved by a factor of 5. Evidence of covalent bonding between agent and glass was found for three of the coupling agents investigated, namely: 3-aminopropyltriethoxysilane; etidronic acid and hexamethylene diisocyanate. These three coupling agents also improved the interfacial shear strength and increased the hydrophobicity of the glass surface. It is expected that this would provide an improvement in the macroscopic properties of full-scale composites fabricated from the same materials which may also help to retain these properties for the desired length of time by retarding the breakdown of the fibre/matrix interface within these composites.
In this article, we, for the first time, investigated mesoporous bioactive glass scaffolds for the delivery of vascular endothelial growth factor. We have found that mesoporous bioactive glass scaffolds have significantly higher loading efficiency and more sustained release of vascular endothelial growth factor than non-mesoporous bioactive glass scaffolds. In addition, vascular endothelial growth factor delivery from mesoporous bioactive glass scaffolds has improved the viability of endothelial cells. The study has suggested that mesopore structures in mesoporous bioactive glass scaffolds play an important role in improving the loading efficiency, decreasing the burst release, and maintaining the bioactivity of vascular endothelial growth factor, indicating that mesoporous bioactive glass scaffolds are an excellent carrier of vascular endothelial growth factor for potential bone tissue engineering applications.
Aneurysmal bone cyst is a benign, locally destructive lesion of bone. Based on progressive cortical thinning pathological fractures are common, and are often the presenting feature. Despite the long experience of orthopaedists, radiologists and pathologists with aneurysmal bone cyst there is limited knowledge regarding the cause of the lesion and optimal treatment. Common methods of treatment vary considerably in the literature, particularly in children. A large variety of bone substitutes have been used to fill the cystic lesions. To date there has been no graft material which can be regarded as completely satisfactory. Our experience with freshly isolated autologous bone marrow derived mononuclear cells combined with β-tricalcium phosphate and absorbable atelocollagen for bone formation is presented. The concept of this treatment is based on stimulation of natural events continuously present in living bone appear to be a reasonable and beneficial alternative to promote healing of bone cysts and offering both osteoinduction and osteoconductive features.
The vitreous body can be regarded as a fascinating simple but important tissue, since it represents the main compartment of the eye and plays a crucial role for proper vision. Several diseases require its removal with following substitution using a liquid artificial vitreous body replacement. We explore the biocompatibility of a poly(AMPS-Na+)-graft-poly(NIPAAm) polyelectrolyte following the innovative concept of thermo-responsive behaviour, exhibiting enhanced shear viscosity at physiological temperatures. As a powerful model for the blood-retinal barrier, we use the well-established in vitro cell culture model based on highly differentiated porcine brain capillary endothelial cells. Via the quantification of the transendothelial electrical resistance and immunocytochemical staining of tight junction proteins, we are able to show that a barrier integrity affecting impact of the polyelectrolyte was only transient and nearly reversible. Furthermore, the polyelectrolyte hydrogel is characterized by the absence of any acute cell morphology, cell vitality or proliferation affecting impacts. It does not trigger acute apoptotic processes, as can be substantiated via caspase-3 activity and DNA fragmentation assays. In view of the results of this study, it is shown that the polyelectrolyte does not affect the vitality parameters of our porcine brain capillary endothelial cells. It can be suggested that the tested thermo-responsive polyelectrolyte does not affect the sensitive retinal barrier integrity. Thus from the cellular tolerance it might serve as a potential liquid artificial vitreous body replacement to overcome the most prominent difficulties of common vitreal endotamponades.
Conventional and silicone hydrogels as models for contact lenses were prepared to determine the effect of the presence of hyaluronic acid on lysozyme sorption and denaturation. Hyaluronic acid was loaded into poly(2-hydroxyethyl methacrylate) and poly(2-hydroxyethyl methacrylate)/TRIS – methacryloxypropyltris (trimethylsiloxy silane) hydrogels, which served as models for conventional and silicone hydrogel contact lens materials. The hyaluronic acid was cross-linked using 1-ethyl-3-(3-dimethylaminopropyl)-carbodiimide in the presence of dendrimers. Active lysozyme was quantified using a Micrococcus lysodeikticus assay while total lysozyme was determined using 125-I radiolabeled protein. To examine the location of hyaluronic acid in the gels, 6-aminofluorescein labeled hyaluronic acid was incorporated into the gels using 1-ethyl-3-(3-dimethylaminopropyl)-carbodiimide chemistry and the gels were examined using confocal laser scanning microscopy. Hyaluronic acid incorporation significantly reduced lysozyme sorption in poly(2-hydroxyethyl methacrylate) (p < 0.00001) and poly(2-hydroxyethyl methacrylate)/TRIS – methacryloxypropyltris (trimethylsiloxy silane) (p < 0.001) hydrogels, with the modified materials sorbing only 20% and 16% that of the control, respectively. More importantly, hyaluronic acid also decreased lysozyme denaturation in poly(2-hydroxyethyl methacrylate) (p < 0.005) and poly(2-hydroxyethyl methacrylate)/TRIS – methacryloxypropyltris (trimethylsiloxy silane) (p < 0.02) hydrogels. The confocal laser scanning microscopy results showed that the hyaluronic acid distribution was dependent on both the material type and the molecular weight of hyaluronic acid. This study demonstrates that hyaluronic acid incorporated as a wetting agent has the potential to reduce lysozyme sorption and denaturation in contact lens applications. The distribution of hyaluronic acid within hydrogels appears to affect denaturation, with more surface mobile, lower molecular weight hyaluronic acid being more effective in preventing denaturation.